background image

3

SECTION 2:  

Congratulations on choosing our product! Please  read all of this  instruction manual carefully and 

keep it safe for future reference.This manual contains all the necessary information for safe 

installation and operation of this product.

This equipment is produced in accordance with CE standards and conforms to international 

standard DMX512.  It can be operated in Master or Slave in phase control. This product is ideal for 

use with large architectural applications,entertainment, theatre,indoor or outdoor stages, etc.

On receiving this product, please carefully check that there has been no damage caused in 

transportation and that the following are enclosed: 

Signal   line  ----------------------- two pieces             User Manual----------------------- one copy

SECTION  3:  SAFETY INSTRUCTIONS

Every person involved with installation and maintenance of this device must be qualified 

and  follow the instructions of this manual

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE OPERATION

CAUTION:

Ø

K

eep this device away from rain and moisture!

Ø

U

nplug mains lead before opening the housing!

Ø

A

lways operate the equipment as described in the user manual

Ø

W

ith a high voltage you can suffer a dangerous electric shock when touching the 

wires!

Ø

T

his device has left our premises in absolutely perfect condition. In order to maintain this 

condition and to ensure safe operation, it is absolutely necessary for the user to follow 

the safety instructions and warning notes in this manual.

IMPORTANT:

Ø

T

he manufacturer will not accept liability for any resulting damages caused by the non-

observance of this manual or any unauthorized modification to the device.

Ø

Please consider that damages caused by manual modifications to the device are not 

subject to warranty.

Ø

Never allow the power-cable to come into contact with other cables! Always handle the 

power-cable and all electrical wiring and connections particular caution!

Ø

Make sure that the supplied voltage is not higher than stated on the rear panel.

Ø

Always ensure that the power-plug is securely connected. Make sure that the power-

switch is set to OFF-position before you connect the device to the mains. The power-

INTRODUCTION

www.carlosmendoza.com.mx

Содержание Showco Arc-Lite 575












Отзывы: