manualshive.com logo in svg

Carlisle Binks 102-2400 FRP, Руководство по обслуживанию

Поделиться
Скачать
Carlisle Binks 102-2400 FRP Скачать руководство пользователя страница 1

77-2520-R15  (5/2019)

1 / 20

www.carlisleft.com

Binks MODELS 102-2400 FRP,

102-2500 GEL-COAT, AND

102-2545 VINYL ESTER 

AIR-ASSISTED AIRLESS

CENTURY SPRAY GUNS

Be sure you understand 

ALL of the following instructions

thoroughly 

BEFORE operating any part of the airless equip-

ment system. 

CONSULT YOUR BINKS REPRESENTA-

TIVE TO CLEAR UP ANY ITEMS OF INSTRUCTION
YOU DO NOT UNDERSTAND.

1. Under no circumstances should the spray gun be carelessly

handled nor its spray (even when the nozzle is removed)
directed at close proximity at any part of the human body.

2.

NEVER clean, change, or remove nozzle from the spray

gun without doing the following:
a. Lock trigger (62) by pushing forward. Rotate locking

block in upward position.

b. Shut off pump and turn off air supply.
c. Release fluid pressure in the entire system, from pump

to spray gun. Stop pump in down position.

3.

NEVER attempt to force the flow of liquid backward

through the gun.

4.

NEVER plug a hose leak with your finger, with adhesive

tape, or other “stop-gap” device.

5.

NEVER operate the airless system with a defective hose.

ALWAYS replace the defective hose immediately. For

continuing safety, users are urged to:
a.

ALWAYS handle carefully all hose connections, joints,

and seating surfaces on the spray gun to prevent dam-
age.

b.

NEVER kink or bend the fluid hose into less than a

four inch radius.

c.

FREQUENTLY check the hose for kinks or abrasions.

These may develop into a rupture.

d.

NEVER use standard hardware to modify the airless 

system. 

ALWAYS use Binks high pressure fittings

only.

6. The airless pump must be grounded before operating the 

airless system.

WARNING — HIGH PRESSURE — WARNING

UP TO 3500 POUNDS PER SQUARE INCH

•

DO NOT POINT SPRAY GUN AT ANY PART OF THE HUMAN BODY

•

FLUID UNDER HIGH PRESSURE CAN PENETRATE THE SKIN AND CAUSE SEVERE INTERNAL INJURY

•

IN CASE OF INJURY OBTAIN MEDICAL ATTENTION IMMEDIATELY

•

BE SURE TO REPORT NATURE OF INJURY AND TYPE OF FLUID OR SOLVENT TO THE DOCTOR

AIR ASSIST 

AIR CAP

CATALYST

INJECTOR

CATALYST FILTER

CENTURY TIP

TRIGGER LOCK

AIR ASSIST INLET 

1/4 NPS(m) / 1/4 NPT(m)

CATALYST INLET

1/4 NPS(m)

RESIN INLET 

1/4 NPS(m) (102-2400 & 102-2500)

3/8 NPS(M) (102-2545)

102-2400 Century Wet-Out Gun
111-4052

Wrench

102-2521

Catalyst Injector

102-2526

Catalyst Injector

102-2531

Catalyst Injector

106-1170

Start Up Kit

102-2494

Night Cap

102-2500 Century Gel-Coat Gun
111-4052

Wrench

102-2515

Catalyst Injector

102-2518

Catalyst Injector

102-2521

Catalyst Injector

106-1170

Start Up Kit

102-2494

Night Cap

102-2545 Century Vinyl Ester Gun
111-4052

Wrench

102-2521

Catalyst Injector

102-2526

Catalyst Injector

106-1170

Start Up Kit

102-2494

Night Cap

CHOPPER INLET 

(not shown—see page 4)

EN

SERVICE MANUAL

AIR-ASSISTED AIRLESS  

CENTURY SPRAY GUNS

MODELS 102-2400 FRP, 102-2500 GEL-COAT,  

AND 102-2545 VINYL ESTER

Содержание Binks 102-2400 FRP





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды