background image

0

Cardo S-800

Problem

Action

Battery does 
not provide 
at least six 
hours of talk 
time

Make sure your headset is fully charged.
Charging time is up to 2 hours for an empty battery. 
When fully charged and charger is connected to 
headset, the red light indicator turns off.

NOTE

: You may have compromised the battery’s 

capacity if you did not fully charge it prior to initial use.

Red Status 
Light does not 
light steady 
when charger is 
connected.

1. Make sure the wall charger is firmly plugged into 

the Charging Jack.
2. Disconnect the charger from the Charging Jack, 
wait a few seconds and plug it back in.
3. When the headset is fully charged, the
red light turns off.

Bad sound 
quality

1. Possibly caused by nearby interference.
2. If you have a GSM phone and your
headset is too close to the phone, interference may occur.
3. Headset and mobile phone are more than 30 ft. 

(10m) apart. Range will be shortened if there are major 

obstacles between the Headset and mobile phone.

I press the 
buttons and
nothing happens

Your headset is probably in key lock mode. Unlock the 
Headset as described above.

Содержание S-800































Отзывы: