Cardinal Health Alaris 8000 Series Скачать руководство пользователя страница 120

Страница: 120 / 378

2-64

Programming

Alaris

System Directions for Use

Pump and Syringe Modules Section

Multidose Mode

(Continued)

CHANNEL
SELECT

CHANNEL

OFF

RESTART

PAUSE

ALARM

INFUSE

STANDBY

ALARM

INFUSE

STANDBY

CHANNEL
SELECT

CHANNEL

OFF

PAUSE

RESTART

RATE (mL/h)

Current time

displayed is correct, press

CONFIRM

soft

key; otherwise, press

Change Time

and enter correct

time. (Reference "System Options", "Time of Day" in PC
Unit Section of this

DFU

Press

VOLUME DURATION

soft key.

To enter volume to be infused for each dose, use numeric
data entry keys.

To enter duration for each dose, press

DURATION

soft key

and use numeric data entry keys.

To enter time interval (

hours) between doses,

press

DOSE INTERVAL

soft key and use numeric data

entry keys.

To enter number of doses, press

# OF DOSES

soft key

and use numeric data entry keys.

• If Delay Options is enabled,

DELAY OPTIONS

soft key

appears.

To begin multidose infusion, press

START

soft key.

• Main Display shows remaining

VTBI

for that dose.

• At completion of a multidose program,

MULTIDOSE

COMPLETE

appears on Main Display.

Multidose

Time of Day

Change

Time

Current time:

08:00

CONFIRM

>CONFIRM Time-of-Day

Volume/Duration Enabled

Содержание Alaris 8000 Series



























































































































































































































































































































































































Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Похожие инструкции для Alaris 8000 Series

Бренды по названию

Популярные бренды

Cardinal Health Alaris 8000 Series, Инструкция по применению

Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Похожие инструкции для Alaris 8000 Series

Бренды по названию

Популярные бренды