Cardinal Health Alaris 8000 Series Скачать руководство пользователя страница 121

Страница: 121 / 378

Programming

2-65

Alaris

System Directions for Use

Pump and Syringe Modules Section

To see detail screen during or between infusions, press

CHANNEL SELECT

key.

• During infusion,

Volume Remaining

displays.

• Between infusions:

♦

Number of doses completed and when next dose
starts display.

♦

Yellow Standby Status Indicator illuminates.

NOTES:

If the current time has been previously confirmed, the

Time of

Day

screen will not be displayed.

RATE

is calculated with each keystroke for

DURATION

Reference"Delay Options" procedure to program an infusion
delay. When delaying an infusion, a multidose cannot be
delayed for more than

hours, and all doses in the multidose

program must be completed within a

-hour program.

Syringe Module: If

NEOI

is enabled, the Near End of infusion

message appears near the end of the last dose.

To enter rate, use numeric data entry keys.

To enter volume to be infused for each dose, press

VOLUME/DOSE

soft key and use numeric data entry keys.

To enter time interval (

hours) between doses,

press

DOSE INTERVAL

soft key and use numeric data

entry keys.

To enter number of doses, press

# OF DOSES

soft key

and use numeric data entry keys.

• If Delay Options is enabled,

DELAY OPTIONS

soft key

appears.

Volume/Duration Enabled

(Continued)

Volume/Duration Disabled

Multidose Mode

(Continued)

CHANNEL

SELECT

CHANNEL

OFF

RESTART

PAUSE

ALARM

INFUSE

STANDBY

ALARM

INFUSE

STANDBY

CHANNEL

SELECT

CHANNEL

OFF

PAUSE

RESTART

RATE (mL/h)

Содержание Alaris 8000 Series



























































































































































































































































































































































































Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Похожие инструкции для Alaris 8000 Series

Бренды по названию

Популярные бренды

Cardinal Health Alaris 8000 Series, Инструкция по применению

Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Похожие инструкции для Alaris 8000 Series

Бренды по названию

Популярные бренды