background image

CARBATEC.C OM.AU

9

DC-1200P

25. 

ALWAYS WEAR A DUST MASK TO 
PREVENT INHALING DANGEROUS DUST 
OR AIRBORNE PARTICLES,

 including wood 

dust, crystalline silica dust and asbestos 
dust. Direct particles away from face and 
body. Always operate tool in well ventilated 
area and provide for proper dust removal. Use 
dust extraction system wherever possible. 
Exposure to dust may cause serious and 
permanent respiratory or other injury, 
including silicosis (a serious lung disease), 
cancer, and death. Avoid breathing dust, and 
avoid prolonged contact with dust. Allowing 
dust to get into your mouth or eyes, or lay on 
your skin may promote absorption of harmful 

material. Always use properly fitting AS/NZS 

approved respiratory protection appropriate 
for the dust exposure, and wash exposed 
areas with soap and water.

SAFETY INSTRUCTIONS

26. 

USE A PROPER EXTENSION CORD IN GOOD 
CONDITION.

 Use of extension cords should 

be avoided where possible. When using an 
extension cord, be sure to have a cord heavy 
enough to carry the current your product will 

draw, and with compatible pin configuration 

and connections. NEVER use an extension 
cord rated at less than your machine. 
Longer run extensions will need heavier 
duty extension cords. Only connect your 
extension cord or machine to a receptacle 
that accepts your plug and never modify your 
plug to suit a receptacle.

DUST COLLECTOR SAFETY

INTENDED USE

This dust collector is only intended for collecting 
wood dust and chips from woodworking 
machines. Do not use this dust collector to collect 
metal, dirt, pebbles, drywall, asbestos, lead 

paint, silica, liquids, aerosols, or any flammable, 

combustible, or hazardous materials. 

HAZARDOUS DUST

Dust created while using machinery may cause 
cancer, birth defects, or long-term respiratory 
damage. Be aware of dust hazards associated with 
each work piece material, and always wear a  
AS/NZS-approved respirator to reduce your risk.

DUST ALLERGIES 

Dust from certain woods may cause an allergic 
reaction in people and animals. Make sure you 
know what type of wood dust you will be exposed 
to in case there is a possibility of an allergic 
reaction.

WEAR A RESPIRATOR

Fine dust that is too small to be caught in the filter 

will be blown into the ambient air during operation. 
Always wear a AS/NZS-approved respirator during 
operation and for a short time after to reduce your 
risk of permanent respiratory damage.

Содержание DC-1200P

































Отзывы: