background image

 

 

 

 Version 23.11.2020 

HW: CAM(V98/(V12) 

CI-RL4-UCON8-LV 

P

a

g

e

6

 

 
1.4.1.

 

Activating the front camera input (dip 1) 

 

If set to ON, the interface switches for 10 seconds from the rear-view camera to the front 
camera input after having disengaged the reverse gear. In addition, a manual switch-over to 
the front camera input is possible via keypad (short press) from any image mode. 
 
Description of the power supply output: see chapter “Power supply output”. 
 

1.4.2.

 

Enabling the interface’s video inputs (dip 2-3) 

 

Only the enabled video inputs can be accessed when switching through the interface’s video 
sources.  It is recommended to enable only the required inputs, disabled inputs will be 
skipped when switching through the video-interfaces inputs. 
 

1.4.3.

 

Rear-view camera setting (dip 5) 

 

If set to OFF, the interface switches to factory picture while the reverse gear is engaged to 
display factory rear-view camera. 
If set to ON, the interface switches to its rear-view camera input 

„Camera-IN“ 

while the 

reverse gear is engaged. 
 

1.4.4.

 

Monitor selection (dip 7 and 8) 

 
Dips 7-8 customize the monitor-specific video settings which cannot be predicted as even 
within the same head-unit version, the monitor specifications may vary. It is necessary to try 
all possible combinations - while a working video source is connected to the chosen input of 
the interface - to see which combination gives the best picture quality and size (some may 
give no picture). It is possible to first hot plug through the dip combinations, but if you do 
not experience any change of picture after trying all options, retry and disconnected the 6pin 
power plug of the video-box between every change of the dip setting. 
 

Note:

 Dips 4 und 6 are out of function and have to be set to 

OFF

 
 
1.5.

 

Settings of the 4 Dip switches (CAN function - red) 

 
Dip position down is 

ON

 and position up is 

OFF

 

Navigation / System 

Dip 1 

Dip 2 

Dip 3 

Dip 4 

All vehicles 

OFF 

OFF 

OFF 

OFF 

 
For all vehicles, use the OFF position of all the 4 dip switches. 
 

 

After each Dip-switch-change a power-reset of the Can-box has to be performed! 

 

 

 

Содержание CI-RL4-UCON8-LV
























Отзывы: