Caple Pi401, Инструкция по эксплуатации

Страница: 6 / 16

6
seat. Lift the hood together with the structure
and the extension tubes to make the four
springs (Fig. 7.6-E) hook to the slots (Fig.
7.3-C). Then tighten the two elements secu-
rely (Fig. 6.1 & Fig. 6.2) with the safety screws
(Fig. 6.2-A) and connect the hood tube to the
drain hole.
Make the electrical connections. (For versions
with display only) Lift the lower pipe until the
cable strap coming out of the sucking unit is
uncovered and connect it to the display cable
strap. Put down the lower pipe while paying
attention it is being properly introduced into
the hood.
Lift the upper tube (Fig. 7.5) up to the ceiling
and insert the two self-tapping screws (Fig.
7.5-D).
Filtering model
Place the upper plate (Fig.5.1) on the ceiling.
Drill 4 holes, 8 mm each, just next to the
slots. Insert the plastic dowels into the holes
(Fig.5.1-A). Fix the baffle (Fig. 5.2) to the up-
per bracket (Fig.5.3) with the four selftapping
screws provided (Fig. 5.3 A). Screw up the pla-
te together with the baffle (Fig.5.1 B). Then
fasten the lower structure (Fig. 7.2) on the
hood by making its holes and the metricthre-
ad screws welded on the fan support coincide
(Fig. 7.1). Insert the washers and nuts provi-
ded (Fig. 7.2-A) and screw with an appropriate
tool. Connect the drainpipe to the power unit
nozzle and fix securely with a hose clamp. In-
sert the upper structure (Fig. 7.3) into the lo-
west one and adjust its height as required by
matching it with the cooking top’s minimum
height. Tighten the two structures securely
with the screws provided (Fig. 7.3-B). Insert
the two extension tubes (Fig. 7.4 & Fig. 7.5)
from above the two structures by making them
come down to the appropriate hood seat.
Lift the hood together with the structure and
the extension tubes to make the four springs
(Fig. 7.6-E) hook to the slots (Fig. 7.3-C).
Then tighten the two elements securely (Fig.
6.1 & Fig. 6.2) with the safety screws (Fig. 6.2-
A) and connect the hood tube to the baffle’s
lower hole.
Make the electrical connections. (For versions
with display only) Lift the lower pipe until the
cable strap coming out of the sucking unit is
uncovered and connect it to the display cable
strap. Put down the lower pipe while paying
attention it is being properly introduced into
the hood. Lift the upper tube (Fig. 7.5) up to
the ceiling and insert the two self-tapping
INSTALLATION
Before installing the appliance, make sure
that none of the parts is damaged in any way.
In case of damaged parts, contact your retai-
ler and do not proceed with installation.
Read all of the following instructions with
care before installing the appliance.
- Use an air outlet pipe of the shortest pos-
sible length.
- Limit the number of pipe bends.
- Use a material approved by standards and
regulations.
- Avoid any sudden changes in pipe section
(recommended constant diameter: 150 mm
or equal surface area).
Attention: at least two people are needed
to perform the installation.
Before installing the appliance, in order not to
damage the appliance itself, the metal grease
filter should be removed. Such filter can be
removed by pushing the special filter handle
toward the back side of the cooker hood and
turning it downwards so to unfasten it from
its slot (Fig. 3 A).
Before fixing the hood, place the electric fe-
eding properly into the ornamental pipe and
place a hole for air evacuation in case of a
sucking version.
Suction model
Place the upper plate (Fig.5.1) on the ceiling.
Drill 4 holes, 8 mm each, just next to the
slots.
Insert the plastic dowels into the holes
(Fig.5.1-A) and screw up the plate on the cei-
ling (Fig. 5.1-B). Then fasten the lower struc-
ture (Fig. 7.2) on the hood by making its ho-
les and the metric-thread screws welded on
the fan support coincide (Fig. 7.1). Insert the
washers and nuts provided (Fig. 7.2-A) and
screw with an appropriate tool.
Connect the drainpipe to the power unit noz-
zle and fix securely with a hose clamp.
Insert the upper structure (Fig. 7.3) into the
lowest one and adjust its height as required
by matching it with the cooking top’s mini-
mum height. Tighten the two structures se-
curely with the screws provided (Fig. 7.3-B).
Insert the two extension tubes (Fig. 7.4 & Fig.
7.5) from above the two structures by making
them come down to the appropriate hood