GAS CONNECTING
2
1
3
4
5
L
N
A
A special valve for routinely turning the gas supply on/off must be
installed between the gas inlet tube to the room and the hob, in
order to cut off the gas supply after cooking in the event of accidents
during cooking. This valve must be easily accessible at all times
and should be closed during long periods of no use.
The gas tube must be routed in such a way that it is not fed through
hot areas and does not come into contact with any hot parts of
the appliance, e.g. the underside of the hob. Tube installation must
be carried out in such a way as to ensure that it runs freely and
that it cannot come into contact with or be bent by any movable
parts in the kitchen, e.g. drawers.
If this is not the case, a special pressure regulator must be fitted
to the gas supply pipe in accordance with the relevant standards.
The cooker must be connected to the gas supply pipe such that
the cooker is not subjected to any kind of stress.
This appliance must be installed by a qualified electrician / competent
person
gas safe register.
Safety may be impaired if installation
is not carried out in accordance with these instructions.
This appliance shall be installed in accordance whit the regulations
in force and only in a well-ventilated space. Read the instructions
before installing or using this appliance.
IMPORTANT
We recommend to check wether the appliance has been foreseen
for the kind of gas distributed. Conversion for use other gases
must only be undertaken by a qualified person. For information for
use on other gases contact your local Service Centre. The cooker
must be installed by a qualified person, conforming to local
regulations. Failure to install the appliance correctly could invalidate
any manufacturers warranty and lead to prosecution under the
above quoted regulations.
In order to guarantee that the cooker works safely and has a
moderate energy consumption and long service life, you must
ensure that the supply pressure corresponds to the values given
in table D.
Provision for Ventilation
The room containing the cooker should have an air supply in
accordance with local regulations.
Remember that the quantity of air necessary for combustion must
never be less than 2m3/h for each kW of power (see total power
in kW on the appliance data plate).
Gas Safety (Installation & Use) Regulations
It is the law that all gas appliances are installed by competent
persons in accordance with the current edition of the
Installation
& Use Regulations.
It is in your interest and that of safety to
ensure compliance with the law.
The appliance must be installed in accordance with All relevant
British Standards (latest editions).
Gas Connection
Prior to installation, ensure that the local distribution conditions
(nature of the gas and gas pressure) and the adjustment conditions
are compatible. The adjustment conditions for this appliance are
stated on the rating plate which can be found on the back cover.
This appliance is not designed to be connected to a combustion
products evacuation device. Particular attention should be given
to the relevant requirements regarding ventilation.
Connection to the cooker should be made with connection in
accordance with local regulations.
ELECTRICAL CONNECTION
This appliance must be installed by a qualified person in
accordance with the latest edition of the IEE Regulations and
in compliance with the manufacturer instructions.
Ensure that the voltage is the same as that stated on the rating
plate. The rating plate which can be found on the inside of the
front appliance drawer.
WARNING! THIS APPLIANCE MUST BE EARTHED
The power supply must be fitted with a disconnect switch in which
the distance between contacts permits total disconnection in
accordance with overvoltage category III, as required by installation
regulations.
Be sure that the earth wire green/yellow is not interrupted
by the switch
We recommend that the cooker circuit is rated to 20 amps.
Cable type HO5 RRF 3 X 2.5 mm
2
Connecting the mains cable
Open the mains terminal block cover as shown, unscrew screw
A the cable clamp and unscrew (not fully) the screws in the
mains terminal block L N E which secure the three wires of the
mains cable. Fit the cable and refit screw A the cable clamp.
Allow sufficient cable length for the cooker to be pulled out for
cleaning, but do not let it hang closer than 50mm (2) to the floor.
The cable can be looped if necessary, but make sure that it is not
kinked or trapped when the cooker is in position.
IMPORTANT
The wires in the mains lead are coloured in accordance with the
following code:
GREEN AND YELLOW......EARTH
BLUE .................................NEUTRAL
BROWN.............................LIVE
9
GB
1/2
Содержание CR9206
Страница 2: ......