Use And Care Guide
Flexible LED Strip Light Kit
EN
Model No.: JJ-5050ST-RGB-12 JJ-RGB-33-2 JJ-RGB-50-2
PACKAGE CONTENTS
Description
LED Light Strips (adhesive backs)
DC Adaptor
IR Receiver
Remote Controller(battery included)
Part
A
B
C
D
Quantity
2
1
1
1
A
B
C
D
WARNING
To avoid electrical shock or product failure, this lamp must be used in dry
locations and in open fixtures only.
This product is not a toy and should not be stored or left in locations
accessible to young children.
To avoid possible fire, product damage, or early lamp failure, this lamp
should not be used in heat-producing appliances.
To avoid possible fire hazard, only connect the strip to constant votage 12V
DC.
To prevent early lamp failure, lamp should only be installed in operating
environments ranging between: -14°F to +104°F (-10°C to +40°C).
To prevent early lamp failure, lamp should not be bent roughly in the
position of LED chips. It is suggested that the bent angle should be greater
or equal than 90 degrees.
CAUTION
Pull out the plastic battery barrier sheet from the
battery compartment located on the bottom of the
remote.
When not using this product for extended periods,
remove battery to prevent product damage due to
battery leakage.
Observe proper polarity when changing batteries.
Lamp may not light if battery are inserted
incorrectly.
To prevent danger from explosion or leakage, do
not throw battery into fire or expose them to
excessive heat.
Strip can’t light on after the installation.
Check whether the joint is connected correctly.
Check whether the plastic sheet at the bottom of the IR remote is removed.
Check whether the button battery of the IR remote is out of power.
Strip can’t light on after the installation.
Check whether the shear connection is correct.
Two strips with different luminous colors when lighting on.
Check whether the two strips connecting in parallel.
Correct
Incorrect
Incorrect
Angle≥90°
Angle<90°
SETTING UP
HOW TO USE DIY FUNCTION OF REMOTE CONTROLLER?
TROUBLESHOOTING
1.
Select the location where the strip will be
mounted. Assure that all mounting areas
are free from debris and dust.
2.
Stick the LED strip and press with force,
and then press the whole LED strip
repeatedly.
3.
4.
Connect DC Adaptor to Controller.
Plug in DC Adaptor.
eye
LED brightness adjustment button (up): 7 grades
LED brightness adjustment button (down): 7 grades
Pause/Run button.
0N/OFF button.
LED color buttons (20 colors):
Static red/ Static green/Static blue/ Static white
Static orange/ Static light green
/
Static dark blue
Static milk white/ Static dark yellow/ Static cyan
Static lyons blue/ Static white pink/ Static yellow
Static light blue/ Static purple/ Static green white
Static light yellow/ Static sky blue/ Static brown
Static blue white
Quick button: Speed up color changing under
Jump3, Jump7, Fade3, Fade7 and Flash modes.
Slow button: Speed down color changing under
Jump3, Jump7, Fade3, Fade7 and Flash modes.
Auto button: Automatically change colors under
Jump3, Jump7, Fade3, Fade7 and Flash modes.
Flash button: Flash on and off
Fade 7 button: Gradually 7 colors fade change.
Fade 3 button: Gradually 3 colors fade change.
Jump 7 button: Gradually 7 colors jumpy change.
Jump 3 button: Gradually 3 colors jumpy change
DIY buttons: 6 DIY buttons remember colors you set.
Adjust buttons: Increase/ Decrease red, green
and blue colors.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
R
G
B
W
DIY1
DIY2
DIY3
DIY4
DIY5
DIY6
QUICK
SLOW
AUTO
FLASH
JUMP3
JUMP7
FADE3
FADE7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
R
G
B
W
DIY1
DIY2
DIY3
DIY4
DIY5
DIY6
QUICK
SLOW
AUTO
FLASH
JUMP3
JUMP7
FADE3
FADE7
R
G
B
W
DIY
1
DIY
2
DIY
3
DIY
4
DIY
5
DIY
6
QUI
CK
SLO
W
AUT
O
FLA
SH
JUM
P3
JUM
P7
FAD
E3
FAD
E7
About DIY key, when it's pressed first time, will enter the DIY color mode, you
can adjust the color, per the 6 keys at above to increase or decrease the R/G/B
color freely (pressed this time, will jump out from DIY color mode). It will
automatically save the colors you have adjusted. When next time this key is
pressed,it will show the color you saved from last time.
RELEASE
Arrow to Arrow
MADE IN CHINA
Email: [email protected]
Web: www.capetronix.com
WhatsApp: +86 181 2642 9748
