CANYON FURNITURE COMPANY
A.- (1) HEADBOARD
B.- (1) 3 DRW STUDENT LOFT DESK
C.- (1) 5 DRW STUDENT LOFT CHEST
M.- (1) CASTER BED HEADBOARD
D.- (1) LOFT BED END
E.- (2) METAL DOWEL PINS
J.- (6) 1 1/4" SCREW
F.- (4) SIDE RAILS
G.- (2) GUARD RAILS
H.- (24) 5/16" X 4" HEX TAP BOLTS
I.- (24) 5/8" CROSS DOWEL NUTS
J.- (24) 5/16" FLAT WASHERS
K.- (1) 5MM ALLEN WRENCH
L.- (4) 39" SLATS
M.- (8) 1 1/4" SCREWS
N.- (1) HEADBOARD
Q.- (4) 54" SLATS
O.- (1) FOOTBOARD
M.- (8) 1 1/4" SCREWS
P.- (4) CASTER SOCKETS
1.- ASSEMBLE TWIN LOFT BUNK BED, USING ONE HEADBOARD ( A),ONE LOFT BED END ( D),TWO SIDE RAILS ( F),TWO GUARDRAILS ( G), 3 DRW STUDENT DESK (B) OR 5 DRW STUDENT
CHEST(C).
2.- TAKE 3 DRAWER STUDENT DESK (B) OR 5 DRAWER STUDENT CHEST (C), THEN PLACED THEM IN DESIRED POSITION IN THE ROOM,
(PLACE FRONT FACE OF DESK OUTWARDS)
3.- INSERT ONE METAL DOWEL PIN (E) IN EACH OUTSIDE CORNER OF 3 DRW LOFT DESK OR 5 DRW LOFT CHEST, TAKE THE LOFT BED END, AND PLACE IT ON TOP OF DESK OR CHEST
ALIGNING THE METAL DOWEL PIN WITH EACH PRE - DRILLED HOLE IN EVERY END OF THE LOFT BED END UNTIL THE METAL DOWEL PIN ARE ALL THE WAY IN THE HOLE OF THE BED, SEE FIG.9
4.- INSERT TWO CROSS DOWEL NUTS (I) INTO THE SIDE RAIL AND GUARDRAILS HOLES, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.10
5.- ATTACH TWO SIDE RAILS & TWO GUARD RAILS TO HEADBOARD&LOFT BED END, INSERTING TWO HEX TAP BOLTS (H) TWO WASHERS (J) INTO HEADBOARD&LOFT BED END HOLES,
USE THE 5MM ALLEN WRENCH (K) TO TIGHTEN BOTH HEX TAP BOLTS,
(DO NO TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER)
, SEE FIG.11
6.- REPEAT THE SAME PROCESS ON ALL FOUR CORNERS.
7.- PLACE FOUR SLATS (L) ON TOP SIDE RAIL CLEATS,ONE SLAT IN BOTH HEADBOARD&LOFT BED ENDS,PUSH THE SLAT AGAINST THE BED END POST (FIG.A) AND TWO SLATS IN THE
MIDDLE AT EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT END MUST BE FASTEN WITH ONE 1 1/4" SCREW (M), SEE FIG.12
HARDWARE PACK
(HPK00016)
4 PCS SLAT PACK 4/6 BOX ( 92-646 ) FIG.8
LIST OF CONTENTS
K.- (1) 3 DRAWER NIGHT STAND
3 DRAWER STUDENT LOFT DESK BOX ( 92-710 ) FIG.2 OR
CHARCOAL COLLECTION
HARDWARE PACK
(HPK00095)
TWIN UPPER BUNK BED BOX ( 92-705 ) FIG.4
HARDWARE PACK
(HPK00093)
3 DRAWER NIGHT STAND BOX ( 90-503 )
TWIN LOFT BUNK BED END BOX ( 92-706 ) FIG.1
STUDENT BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 1
L.- (1) DESK TOP
5 DRAWER STUDENT LOFT CHEST BOX ( 92-711 ) FIG.3
CASTER TWIN BED BOX ( 90-707,90-709 )
O.- (4) METAL CASTER SOCKET
N.- (1) CASTER BED FOOTBOARD
4 PCS SLAT PACK 3/3 BOX ( 92-645 ) FIG.6
HARDWARE PACK
(HPK00094)
DESK TOP BOX ( 90-602 )
HARDWARE PACK
(HPK00016)
FULL BED BOX ( 92-709 ) FIG.7
6 PCS SIDE RAILS BOX ( 92-730 ) FIG.5
6 PCS SIDE RAILS BOX ( 92-730 ) FIG.5
A
FIG.1
FIG.2
B
C
FIG.3
D
E
FIG.4
F
G
H
I
J
K
FIG.5
L
M
FIG.6
N
O
P
FIG.7
Q
FIG.8
FIG.9
YES,
HORIZONTAL GROOVE
FIG.10
FIG.11
FIG.12
FIG. A
NO
REV 01 14/04/2016
PAGE 2 OF 5
KIS01112