CanyCom CMX 252 Скачать руководство пользователя страница 81

Страница: 81 / 94

Maintenance

-72-

Filling

UPPER

LEVEL

LOW

ER L

EVEL

Filler Cap

5321M-0510-020E

1.  Remove front cover.
2.  Remove battery.
3.   Remove filler cap.
4.   Fill distilled water to "UPPER LEVEL" line.
5.  Install filler cap.
6.  Install battery.
7.  Install front cover.

5116M-0509-040E

1.  Remove front cover.
2.  Remove battery from machine.
3.  Follow instructions in battery charger user's

manual to charge battery.

4. When battery is fully charged, install battery

back in place.

5. Install front cover back in palce.

Charging

Circuit Breaker and Fuses

• If a circuit breaker trips or a fuse blows, investigate the cause before resetting

or replacing.

• Always replace a fuse with one of the correct rating.

• Circuit Breaker: for Mower Deck Slide
• Main Fuse: 30A
• Lights/Mower Deck Lift Fuse: 10A
• Replacement Fuse: Page 50.

NOTE

Содержание CMX 252































































































Результаты поиска

Содержание CMX 252

Отзывы:

Похожие инструкции для CMX 252

Бренды по названию

Популярные бренды

CanyCom CMX 252, Руководство оператора

Результаты поиска

Содержание CMX 252

Отзывы:

Похожие инструкции для CMX 252

Бренды по названию

Популярные бренды