manualshive.com logo in svg

Cantium Scientific MicroBio MB2, Руководство по эксплуатации

Поделиться
Скачать
Cantium Scientific MicroBio MB2 Скачать руководство пользователя страница 46

Connecting the Control Unit and 
remote Sampling Head

The  connectors  are  polarised  so  that 
they  can  only  be  connected  in  the 
correct  manner.  The  remote  head  unit 
requires  the  female  connector  and  the 
male  connector  end  of  the  cable 
connects to the control unit.

Operation

Once  installed,  the  MB2-RSH  operates  in  exactly  the  same  way  as  a 
conventional MB2 bioaerosol sampler.

Calibration - 

Factory or Service Agent only

The MB2-RSH can be calibrated in the same manner as any other MicroBio 
bioaerosol sampler.

Disconnect  the  head  and  control  unit  from  the  cable  and  return  to  the 
manufacturer  or  approved  agent  for  calibration.  Head  units  must  be 
thoroughly cleaned, sterilised and free from any potential contaminant before 
return  to  a  calibration  agent.  Documented  evidence  of  cleaning  must  be 
provided.  Please  inform  the  calibration  provider  of  the  length  of  the 
connecting  cable  used  for  the  controller  and  head  combination.  It  may  be 
possible  to  calibrate  in  situ. The  use  of  the  Qualisair  ™  qCR  kit  is  required 
for this.

45

Содержание MicroBio MB2

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды