2/2
© 2022.10 CANON INC.
BT1-D018-A-ENG
3-8. IS Operation
ON/OFF operation of IS function (Image Stabilizer) becomes possible when used with the lens with
IS function.
Lens IS function ON : LED next to the IS switch is lit (green)
Lens IS function OFF : LED next to the IS switch is off
To activate IS function, press IS switch. For details, refer to the operation manual for the lens.
3-9. MEMO Switch
The MEMO switch is used to set the framing preset function.
3-10. Zoom Track Function
（
Tracking
）
The zoom control range (zoom track) can be restricted.
This function provides that the range can be virturally set at any position.
(Both the Tele and Wide ends are within a limited area.)
[How to store the memory position for zoom track]
1
.
Zoom to any desired zoom track position (Tele side or Wide side) to be memorized by the
thumb ring operation.
2
.
Move to “MEMO” side on the zoom track switch.
3
.
By above steps (1) and (2), the memory position on each of the Tele and Wide sides is
stored. Also, storing only on either side is possible.
To change the setting, perform step 1 to 2. (The position set last overwrites the setting in
the memory.)
NOTE
1. The memory position of the zoom track can be stored once on each of the Tele and Wide
sides. However, the zoom track memory cannot be stored more than one on each of the
Tele and Wide sides.
2.
The stored memory remains, even after the power is turned off.
3. When a zoom track position has been set already, and of the zoom track position changes
as a new position that goes over from the restricted range of the telephoto end and the
wide-angle end, turn the zoom track switch off so that the new zoom track position can be
set.
[ON / OFF for the zoom track function]
The ON / OFF for the zoom track function indicates as follows:
ON : Virtual zoom control range
Press “ON” side on the zoom track switch.
OFF : Normal zoom control range
Press “OFF” side on the zoom track switch.
NOTE
In case the present zoom position is outside of the restricted range when the zoom track
function turns on, the lens will automatically zoom to the end position of the restricted range.
3-11. Framing Preset Function
This framing preset function can be moved at the maximum speed from any zoom position (optional
position) to a previous memory zoom position by pressing the frame preset switch.
[How to store the framing preset position]
1. Zoom to any desired framing preset position to be memorized by the thumb ring operation.
2. Press the frame preset switch while holding down the MEMO switch. The memory position
will be stored.
[How to recall the framing preset position]
Press the frame preset switch.
NOTE
1. When the zoom track function is activated, and if the framing preset position is outside of
the zooming range under the restriction by the zoom track function, the zoom track function
has a priority.
2. The stored framing preset position remains in the memory, even after the power is turned
off.
All rights reserved. No part of
this operation manual may be
reproduced or copied in any from
or by any means without the
written permission of Canon Inc.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
GENERAL SAFETY INFORMATION
The safety warnings and cautions provided on the product or in this operation manual must be observed.
Failure to observe these warnings and cautions provided to guard against hazards may result in injury
or accident. Read this operation manual carefully to familiarize yourself with its contents and ensure
that you can operate the product properly. Also, keep this manual in a safe place where it can easily be
referenced whenever required.
This manual uses the following symbols and terms in the warning and caution notices for preventing accidents
and protecting the safety of the customer and others.
WARNING
This indicates a potentially hazardous situation which, if not heeded, may
result in death or serious injury to you or others. Be sure to heed all warning
notices to ensure safe operation at all times.
CAUTION
This indicates a potentially hazardous situation which, if not heeded, may
result in a minor injury to you or others, or damage to property. Be sure to
heed all caution notices to ensure safe operation at all times.
NOTE
This indicates cautions and recommendations for operation. It contains
information which, if not heeded, may result in this product failing to function
properly. These notices also contain useful information for operation.
HANDLING THE PRODUCT
WARNING
1.
Do not get this product wet or allow liquid inside. If water gets inside, stop using the product
immediately. Continuing to use the product under this condition may cause a fire or electric shocks.
2. Be sure to hold the connector when disconnecting the cable. Pulling on the cable may sever or
damage it and pose a risk of a fire or electric shocks from a short circuit.
CAUTION
1. Be careful not to drop the product when carrying it. Dropping the product may cause injury.
2.
Ensure that all mountings are securely tightened. If a mounting becomes loose, parts may fall off
and cause injury.
3.
Inspect mountings regularly (about every six months to one year) to ensure they are securely
tightened. If a mounting becomes loose, parts may fall off and cause injury.
NOTE
1. Striking or dropping the lens may cause the malfunction of the product.
2. This product is not waterproof. Take measures to avoid direct contact with rain, snow, or moisture.
Otherwise it may cause the malfuction of the product.
3.
In dusty environments, cover the product when attaching or removing the product. If dust enters
inside, it may cause the malfunction of the product.
4. Before use in particular environments, such as places where chemical products are used, contact
your Canon sales representative or dealer. Otherwise it may cause the malfuction of the product.
DEALING WITH ABNORMALITIES
WARNING
If any of the following situations occurs, immediately disconnect the power plug from the power
outlet and contact your Canon sales representative or dealer.
・
Smoke, fumes, or unusual noises
・
Entry of foreign objects (such as liquid or metal objects) inside the product
MAINTENANCE AND INSPECTION
WARNING
Be sure to disconnect the cable and remove the lens from the camera before cleaning outside
of the lens. Do not use benzene, thinner, or other flammable substances to clean the product.
Otherwise it may cause a fire or electric shocks.
NOTE
Routine inspection about once a year is recommended, depending on the conditions and
environment of use. Request overhaul, if needed.
STORAGE
NOTE
Immediately wipe off any moisture on the lens from misty or foggy environments, using a dry
cloth. Seal the lens in a plastic bag with a desiccant (preferably new) to prevent moisture inside.
Otherwise it may cause the mold or the malfunction of the product.
TO THE CUSTOMER
1. Canon shall bear no responsibility for damage resulting from improper operation of this product by
the customer.
2. Canon shall make no guarantees about the product quality, functions, or operation manual
and its marketability and suitability for the customer’s purpose. Moreover, Canon shall bear no
responsibility for any damage, direct or incidental, that results from usage for the customer’s
purpose.
3. The product specifications, configuration, and appearance are subject to change without prior
notice.
4. For further information on repairs, maintenance, or adjustments not mentioned in this operation
manual, contact your Canon sales representative or dealer.
5.
Note that Canon may be unable to undertake servicing or repair of a product if it is modified without
consulting Canon or your Canon sales representative.
