Canon Super G3 FAX Board-AR1, Руководство по обслуживанию

Страница: 33 / 69

5
5
Service Mode
Service Mode
5-11
5-11
Service Mode > Setting of Menu Switch (MENU) > Menu Switch Composition
Service Mode > Setting of Menu Switch (MENU) > Menu Switch Composition
Setting of Menu Switch (MENU)
Menu Switch Composition
<1/3> <READY>
Report Sssw Menu Num Ncu Type IPFAX Print Clear Test
OK
001
002
003
004
005
006
007
008
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
←
（
yyyyy
）
{aaaaa
～
bbbbb}
←
（
yyyyy
）
{aaaaa
～
bbbbb}
←
（
yyyyy
）
{aaaaa
～
bbbbb}
←
（
yyyyy
）
{aaaaa
～
bbbbb}
←
（
yyyyy
）
{aaaaa
～
bbbbb}
←
（
yyyyy
）
{aaaaa
～
bbbbb}
←
（
yyyyy
）
{aaaaa
～
bbbbb}
←
（
yyyyy
）
{aaaaa
～
bbbbb}
No. Function Range of settings
005 NL equalizer 1: ON, 0: OFF
006 telephone line monitor from 0 to 3
007 transmission level (ATT) from 8 to 15 (ex: 15= -15 dBm)
008 V.34 modulation speed upper limit 0:3429, 1:3200, 2:3000, 3:2800, 4:2743, 5:2400
009 V34 data speed upper limit
from 0 to 13
<005: NL Equalizer>
Use it to enable-disable the NL equalizer.
If errors occur often during communication because of the condition of the line, enable (ON)
the NL equalizer.
NOTE:
Any of the following error codes may be indicated at time of transmission because of
the line condition
##100, ##101, ##102, ##104, ##201, ##281, ##282, ##283, ##750, ##755, ##765,
##774, ##779, ##784, ##789
Any of the following error codes may be indicated at time of transmission because of
the line condition
##103, ##107, ##114, ##201, ##790, ##793
F-5-11
T-5-17
<006: Telephone Line Monitor>
Use it to the telephone line monitor function:
0(DIAL): generate the monitor sound of the telephone line using the speaker from the start of
transmission to DIS.
1: generate the monitor sound of the telephone line using the speaker from the start of
communication to the end of it.
2: not used
3(OFF): do not generate the monitor sound of the telephone line usng the speaker.
<007: ATT Transmission Level>
Use it to set the transmission level (ATT).
Raise the transmission level if errors occur frequently at time of communication because of
the condition of the line. (It means close to 8)
NOTE:
Any of the following error codes may be indicated at time of transmission because of
the line condition
##100, ##101, ##102, ##104, ##201, ##280, ##281, ##282, ##283, ##284, ##750,
##752, ##754, ##755, ##757, ##759, ##760, ##762, ##764, ##765, ##767, ##769,
##770, ##772, ##774, ##775, ##777, ##779, ##780, ##782, ##784, ##785, ##787,
##789
Any of the following error codes may be indicated at time of reception because of the
line condition
##103, ##106, ##107, ##201, ##793
<008: V.34 Modulation Speed Upper Limit>
Use it to set an upper limit to the modulation speed (baud rate) for the V.34 primary channel.
When '4 (2743 baud)' is selected, the actual communication is executed with 2400 baud.
<009: V.34 Data Speed Upper Limit>
Use to set an upper limit to the data transmission speed for the V.34 primary channel between
2.4K and 33.6K bps in increments of 2400 bps. (0: 2.4K to 13: 33.6K bps).