Canon iP4200 - PIXMA Photo Printer Скачать руководство пользователя страница 12

Страница: 12 / 57

*1: Only for models supporting CD / DVD printing

*2: Only for models not supporting CD / DVD printing

2-2. Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green

(Power LED), or Alarm LED Lit in Orange)

Resume/Cancel button, the automatic print

head alignment will not be re-done.

is incorrect.

13 times

The remaining ink amount
unknown. [1683]

An ink tank which has once been empty is
installed. Replace the applicable ink tank
with a new one.

Printing with a
once-empty or
refilled ink tank
can damage the
print head.

If printing is
continued without
replacing the "no-
good" ink tank,
press the
Resume/Cancel
button for 5 sec. or
longer to record the
use of a refilled ink
tank.

Note:

After the above
operation, the
function to detect
the remaining ink
amount is disabled.

14 times

Ink tank not recognized. [1684]

A non-supported ink tank is installed (the
ink tank LED is turned off). Install the
supported ink tanks.

15 times

Ink tank not recognized. [1410 to
1419]

An error occurred in an ink tank (the ink
tank LED is turned off). Replace the ink
tank(s).

Access cover open. [1200]

Close the access cover.

Cycles of

blinking in

orange (Alram

LED) and green

(Power LED)

Error [Error code]

Solution

(Replacement of listed parts, which are likely to be faulty)

2 times

Carriage error [5100]

- Carriage unit (QM2-2207)

- Timing slit strip film (QC1-6394)

- Logic board ass'y (QM2-2670)

- Carriage motor (QK1-1500)

3 times

Line feed error [6000]

- Timing sensor unit (QM2-2683)

- Timing slit disk film (QC1-6229)

- Feed roller ass'y (QL2-0925)

- Platen unit (QM2-2202)

- Logic board ass'y (QM2-2670)

- PAPER FEED MOTOR (QK1-1502)

4 times

Purge cam sensor error [5C00] - Purge unit (QM2-2208)

1-7

Содержание iP4200 - PIXMA Photo Printer


























































Результаты поиска

Содержание iP4200 - PIXMA Photo Printer

Отзывы:

Похожие инструкции для iP4200 - PIXMA Photo Printer

Бренды по названию

Популярные бренды

Canon iP4200 - PIXMA Photo Printer, Руководство по обслуживанию

Результаты поиска

Содержание iP4200 - PIXMA Photo Printer

Отзывы:

Похожие инструкции для iP4200 - PIXMA Photo Printer

Бренды по названию

Популярные бренды