manualshive.com logo in svg

Canon imageRUNNER 2420, Список кодов ошибок

Поделиться
Скачать
Canon imageRUNNER 2420 Скачать руководство пользователя страница 13

13 

 

0002 

Reception status error 

Replace the reader control PCB. Replace the 
ADF control PCB. 

E400-
0003 

DF communication error 
Reception interrupt error 

Disconnect and then connect the connector. 
Replace the reader controlled PCB. Replace 
the ADF controller PCB. 

 

Code 

Description 

Remedy 

E490-
0001 

Wrong DF 
The installed DF is not of a supported type. 

Install an ADF that is compatible with the 
machine. 

E500-
0001 

Finisher communication error 
Data communication could not be 
performed normally. It has been retried 
three times in vain. 

Replace the finisher controller PCB. 
Replace the DC controller PCB. 

E503-
0001 

fault in communicatio n with the finisher 
(Finisher-Q3/ Q4) 

 

E503-
0002 

fault in communicatio n between finisher 
and saddle unit 

Replace the finisher controller PCB. 
Replace the saddle controller PCB. Check 
the cable. 

E503-
0003 

fault in communicatio n betweenf inisher 
and punch unit 

Replace the finisher controller PCB. 
Replace the punch drive PCB. Check the 
cable. 

E505-
0001 

fault in the backup memory of the finisher 
(common among all finishers) 
fault in the data stored in backup memory 

Turn off the main power. Check the wiring 
of the DC controller PCB and the finisher 
controller, and check the fuse of the 24-V 
power supply. Thereafter, turn the main 
power back on. 

E505-
0002 

fault in the backup memory of the finisher 
(common among all finishers) 
fault in the EEPROM data of the punch unit 

Replace the punch driver PCB. Replace 
the finisher controller PCB. 

E514-
0001 

fault in stack delivery motor (Finisher-S1) 
When the stack retaining spacer is returned 
to home position, the belt escape home 
position sensor does not go on within 1.5 
sec. 

Replace the finisher controller PCB. 
Replace the stack delivery motor. Check 
the stack delivery drive mechanism. 

E514-
0001 

fault in trailing edge assist motor (Finisher-
Q3/ Q4) 
The home position sensor does not go off 
even when the trailing edge assist motor 
has rotated for a specific period of time. 

Replace the finisher control PCB. Replace 
the trailing edge assist motor. 

E514-
0002 

fault in stack delivery motor (Finisher-
S1)When the stack retaining spacer is 
shifted from home position, the belt escape 
home position sensor does not go off within 

Replace the finisher controller PCB. 
Replace the stack delivery motor. Check 
the stack delivery drive mechanism. 

Содержание imageRUNNER 2420































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды