Canon ImagePress C700 Скачать руководство пользователя страница 28

Страница: 28 / 93

T E C H N I C A L W O R K B O O K

Soiling on the Side of Image (Soiled Print)

This occurs due to the foreign substances (toner, lint, oil, etc.) attached to the surface of the Fixing Belt and the

Pressure Belt. As it is often just a temporary symptom, perform the subsequent work before replacement of the

Fixing Belt Unit or the Pressure Belt Unit.

Clean the belt from (Settings/Registration) > [Adjustment / Maintenance] > [Maintenance] > [Clean

Belt].

2) The soiling may remain even after execution of the cleaning of the belt. If this is the case, execute the

cleaning of the belt again.



NOTE:

•

Before executing the cleaning of the belt, load three (3) sheets or more of plain paper in

the Upper Cassette of the Main Body. It is recommended to use the largest size of paper

from among commonly used papers such as 13” x 19” = 330 mm x 483 mm or 12” x

18” = 305 mm × 457 mm.

•

Cleaning of the belt is unavailable during printing.

Feed Direction

Содержание ImagePress C700






























































































Результаты поиска

Содержание ImagePress C700

Отзывы:

Похожие инструкции для ImagePress C700

Бренды по названию

Популярные бренды

Canon ImagePress C700, Техническое пособие

Результаты поиска

Содержание ImagePress C700

Отзывы:

Похожие инструкции для ImagePress C700

Бренды по названию

Популярные бренды