Canon imagePRESS 1135 Series Скачать руководство пользователя страница 108

Страница: 108 / 242

1 / 31

<Remedy>

Cleaning the Feed Rollers

Roller layout drawing

Unit name

Quantity

Outline of work before cleaning the roller(s)

[B-1] Registration Unit

Remove the Registration Unit.

[B-2] Pickup Feed Unit

Open the Feed Guide.

[B-3] Pickup Unit

Remove the Pickup Unit.

Remove the roller.

[B-4] Duplexing Feed Unit

Open the Feed Guide.

[B-5] Reverse Unit

Open the Feed Guide.

[B-6] Delivery Inner Cover Unit

Open the Feed Guide.

[B-7] Delivery Buffer Unit (Front)

Open the Feed Guide.

Remove the Delivery Inner Cover Unit if

necessary.

[B-8] Outer Delivery Unit

Remove the Outer Delivery Unit.

Cleaning method

CAUTION:

Wipe the rollers with dry lint-free paper. If it is still dirty after wiping it with dry lint-free paper, clean it with

lint-free paper moistened with alcohol.

- If the image failure persists after performing the foregoing cleaning, perform the procedure shown below to

replace the parts.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды