Canon imageFormula DR-6010C Скачать руководство пользователя

Страница: 96 / 142

7-1

Chapter 7

ISIS/TWAIN Driver Settings

This chapter describes the dialog boxes of the ISIS and TWAIN drivers. Please read this chapter

and the ISIS/TWAIN driver’s Help before making driver settings.

7-1 Before Use

This scanner can scan documents ranging in size from business cards and checks to A4 size

documents. It can also scan business cards.

To use the DR-6010C with an ISIS/TWAIN-compliant application, the DR-6010C must first be

selected as the scanner to be used.

This section describes how to select the scanner using CapturePerfect 3.0 (an ISIS-compatible

application program.) As the scanner selection procedure depends on the application program being

used, refer to your application’s user’s manual as needed to select the scanner.

Click the Windows [Start] button, and then click [Programs] ([All Programs] for Windows XP)

[CapturePerfect 3.0]

[CapturePerfect 3.0].

CapturePerfect 3.0 starts up.

Содержание imageFormula DR-6010C















































































































































Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды

Canon imageFormula DR-6010C, Руководство пользователя

Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды