Canon imageFormula DR-6010C Скачать руководство пользователя

Страница: 73 / 142

Chapter 4

Maintenance

4-9

Removing/Attaching the Roller Unit

To remove or attach the roller unit, proceed as follows.

CAUTION

Use caution when removing or attaching the roller unit. Using too much force may lead

to damage or personal injury.

Removing the Roller Unit

Carefully open the upper unit until it stops.

IMPORTANT

When opening the upper unit, do not grasp the roller unit in the center. Doing so may distort

the rollers and lead to feeding errors.

Push the roller lock lever down.

While supporting the roller unit with your hand, slide the roller lock lever to the right.

Содержание imageFormula DR-6010C















































































































































Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды

Canon imageFormula DR-6010C, Руководство пользователя

Результаты поиска

Содержание imageFormula DR-6010C

Отзывы:

Похожие инструкции для imageFormula DR-6010C

Бренды по названию

Популярные бренды