background image

vi

Symbols Used in This Manual

The following symbols are used in this manual to explain 
procedures, restrictions, handling precautions, and 
instructions that should be observed for safety.

WARNING

Indicates a warning concerning operations that may lead to 
death or injury to persons if not performed correctly. To 
use the scanner safely, always pay attention to these
warnings.

CAUTION

Indicates a caution concerning operations that may lead to 
injury to persons, or damage to property if not performed 
correctly. To use the scanner safely, always pay attention
to these cautions.

IMPORTANT

Indicates operational requirements and restrictions. Make 
sure that you read these items carefully to operate the 
scanner correctly, and avoid damage to the scanner.

Hint

Indicates a clarification of an operation, or contains 
additional explanations for a procedure. Reading these 
notes is highly recommended.

How This Manual is Organized

This manual consists of the following chapters.

Chapter 1   Before You Start Using the Scanner

Provides an overview of the scanner

Chapter 2   Basic Operation

Describes the basic uses of the scanner

Chapter 3   Maintenance

Describes routine cleaning and roller replacement

Chapter 4   Practical Examples

Describes displayed messages and troubleshooting 
solutions

Chapter 5   Appendix

Provides a list of specifications and support information

Содержание IMAGE FORMULA DR-7550C





































































Отзывы: