Canon E3730A Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 25

Canon E3730A Скачать руководство пользователя страница 7

E3730A OPERATING INSTRUCTIONS

－ 6 －

Fig.1 Explanation diagram concerning safety

Danger

Electromagnetic wave

Do not operate the klystron tube with the output

waveguide disconnected. Output power of high
frequency is about 7.5 MW and it can cause death
or serious injury.

Ground

Please connect a ground line surely.

Danger

High voltage

Do not remove the safety cover and touch while

operating.

DC voltage of 3.5 kV can cause

death or

serious injury.

Warning

Magnetic field

The magnetic field of 0.13 tesla generated by the

permanent magnet can cause to suck an iron
product and scissors.

Danger

High voltage

Do not remove the safety cover and approach and
touch this section. Pulse voltage of 155 kV can
cause death or serious injury.

Warning

X-ray radiation

X rays are radiated from all aspects of the klystron.

There is fear of injury caused by the X-ray
radiation.

Warning

Magnetic field

The magnetic field of 0.3 tesla generated by the

focusing magnet can cause to suck an iron
product and scissors.

(All aspect of the klystron)

«
...
5
6
7
8
9
...
»

Содержание E3730A


























Отзывы:

Нет отзывов