Canon DU-82 Скачать руководство пользователя страница 51

Страница: 51 / 66

V. MALFUNCTION TROUBLESHOOTING

N-1 Power ON failure

<Possible causes>

1. The duplexing unit is not set correctly.

Action:

Re-set it.

2. Poor connection with the connector of 24 V supply line.

Action:

Reconnect the connector J2001 on the duplexing driver PCB correctly.

3. The duplexing driver PCB failure

Action:

Replace it.

N-2 Side registration motor failure

<Possible causes>

1. Poor connection with the connector of the SIDE REGISTRATION MOTOR DRIVE signal line.

Action:

Reconnect the connector J2005 on the duplexing driver PCB correctly.

2. The side registration motor failure

Action:

Replace it.

3. The duplexing driver PCB failure

Action:

Replace it.

N-3 Duplexing unit motor failure

<Possible causes>

1. Poor connection with the connector of the DUPLEXING MOTOR DRIVE signal line.

Action:

Reconnect the connector J2004 on the duplexing driver PCB correctly.

The duplexing unit motor failure

Action:

Replace it.

3. The duplexing driver PCB failure

Action:

Replace it.

N-4 Reversing roller release solenoid failure

<Possible causes>

1. Poor connection with the connector of the REVERSING ROLLER RELEASE SOLENOID

DRIVE signal line.

Action:

Reconnect the connector J2009 on the duplexing driver PCB correctly.

2. The reversing roller release solenoid failure

Action:

Disconnect the connector J2009 on the reversing roller release solenoid. Measure

the resistance between the connector J2009-1 and J2009-2 of the cable.
If it is not about 50

Ω

, replace the reversing roller release solenoid.

3. The duplexing driver PCB failure

Action:

Replace it.

4 - 7

CHAPTER 4

Содержание DU-82


































































Результаты поиска

Содержание DU-82

Отзывы:

Похожие инструкции для DU-82

Бренды по названию

Популярные бренды

Canon DU-82, Руководство по обслуживанию

Результаты поиска

Содержание DU-82

Отзывы:

Похожие инструкции для DU-82

Бренды по названию

Популярные бренды