Installing the Camera
The procedures for mounting the camera to the ceiling using the indoor dome housing are
described below.
If using an memory card, insert the memory card into the camera before installing (please refer
to the “Installation Guide” included with the camera).
Important
Once the camera is installed to the ceiling, to insert and remove the memory card, the camera must be
removed from the ceiling and the ceiling bracket dismounted.
1
Determine an installation position for the camera and drill holes in the ceiling
Using the included template, line up the directon of the camera, determine the locations of
the backside ceiling bracket mounting holes (three) and the ceiling bracket holes, then drill
the holes ( 165 mm ( 6.50 in.)) into the ceiling.
Use the template with the printed side facing you.
Important
When mounting the indoor dome housing, be sure no shavings enter the dome.
2
Mount the camera to the ceiling bracket
Affix with four included fixing screw (M3).
3
Mount the dust cover to the ceiling bracket
Affix with three included fixing screw (M3).
4
Attach the backside ceiling brackets inside the ceiling
From the inside of the ceiling, insert the protrusions on the backside ceiling brackets through
the mounting holes drilled in step 1.
5
Temporarily tighten screws to the backside ceiling bracket
Temporarily tighten the three included ceiling bracket screws (M4) through the ceiling.
6
Secure the safety wire
Securely attach the safety wire to an anchor or structure. After securing one end of the safety
wire to the ceiling, secure the other end to the camera using the screw that is fastened to the
camera.
7
Connect the LAN cable to the camera through the wiring hole
If AC Adapter (sold separately) or an external power supply is used, connect the power
connector to the camera. Connect cables to external device I/O terminals and audio input/output
terminals as necessary (please refer to the “Installation Guide” included with the camera).
8
Mount the ceiling bracket on the ceiling
Position the ceiling bracket over the screws temporarily tightened in step 5, turn clockwise
to temporarily secure in place, and completely fasten the screws.
9
Attach the dome
Align the (O) mark on the dome with the (I) mark on the ceiling bracket, and turn clockwise
until the (I) mark on the dome aligns with the (I) mark on the ceiling bracket. This procedure
also aligns the ceiling bracket screw hole with the dome fixing screw hole.
10
Affix the dome
To prevent the dome from rotating, attach one dome fixing screw (M2).
11
Reboot the camera when the installation is complete
The camera position is initialized (please refer to the “Operation Guide”).
Note
While the LED is on, light may reflect inside the dome and be captured on video. If this happens, set the
LED setting to [
Turn Off
] (please refer to the “Operation Guide”).
9
8
6
4
2
3
5
7
10
Specifications
Model DR41-C-VB/DR41-S-VB
Type
Clear/Smoked *
Dimensions ( x H) 204 x 176 mm ( 8.03 x 6.93 in.) (Dome: R62 mm (R2.44 in.))
Weight
Approx. 765 g (1.687 lb.) (excluding camera)
* This dome is approximately 50% transparent.
External Dimensions
204 (8.03)
R62
(R2.44)
162 (6.38)
(Max. circumscribed
exterior dimension)
10 (0.39)
7( 0.28)
182 ( 7.17)
176 (6.93)
92 (3.62)
3- 4.6 (
0.18)
(ceiling mount holes)
120°
11
Safety wire
Secure to an
anchor or
structure
LAN cable
Ceiling
bracket
Backside
ceiling
bracket
Ceiling board
Dome
Camera
Fixing
screw
M3 x 3
(included)
Fixing
screw
M3 x 4
(included)
Ceiling bracket screw
M4 x 3
(included)
Unit: mm (in.)