Canon Colorado M Series Скачать руководство пользователя страница 260

Страница: 260 / 378

Configure the network

Introduction

At installation, the printer is connected to the network and connectivity settings are made.

If necessary, you can change the network configuration settings on the user panel.

Network overview

Action

Connection via

The printer receives jobs from the RIP worksta-
tion

RAW TCP/IP (port 9100)

The printer connects via the internet with the
back office

HTTPS (port 443)

The printer connects to the mail server for
password recovery and to inform the adminis-
trator of security updates and new software
versions.

SMTP (port 25 by default, can be changed)

You can access the settings editor

HTTP (port 80) or HTTPS (port 443 by default,
can be changed)

NOTE

HTTPS requires a valid certificate.

Procedure

On the operator panel, tap on the [System] icon on the right.

Tap on [Connectivity ].

Tap on [Identification and network adapter]. You can change the [Hostname], [Adapter link speed
and duplex mode] or [Primary DNS suffix].

NOTE

You have to log in as System administrator to change the settings. For more
information, see

Configure the network

260

Chapter 8 - Configure the network and security settings

Содержание Colorado M Series



























































































































































































































































































































































































Результаты поиска

Содержание Colorado M Series

Отзывы:

Canon Colorado M Series, Руководство по эксплуатации, Страница: 260 / 378

Результаты поиска

Содержание Colorado M Series

Отзывы: