Canon Colorado 1630 Скачать руководство пользователя страница 370

Страница: 370 / 388

Error codes overview

Introduction

When an error occurs you will see an information icon on the operator panel. Click on the icon to
find information on the error.

NOTE

When a job requires a license or a hardware kit such as FLXfinish

and that license or kit is

missing, the job will not appear on the operator panel. The controller will not give an error code.

In the table below you find the most common error codes.

Num
ber

Error code

Message

Action

5713

Cannot read markers
for media step control

• Clean the M&C scanner, see

Clean

the M&C scanner on page 188

• Use the advanced black markers.
• Clean the media or use different me-

dia.

1701
1702
1705
5709

Carriage crash

• Clean the platen and the buffer plate,

see

Clean the platen on page 191

and

Clean the buffer plate on page 194

• Clean the ruler, see

Clean the ruler on

page 253

• Check the fan settings.
• Use uncurled or undamaged media.
• Use the correct winding mode.
• Use recommended media and pro-

files from Canon media guide web-
site.

• Make sure media is not damaged or

curled.

• Make sure the media can be transpor-

ted well.

1760
1761
5760
5761

Carriage position error
during home

• Check if the carriages can move free-

ly (i.e. is not blocked).

• Check if the platen is clean. For more

information see

Clean the platen on

page 191

Error codes overview

370

Chapter 9 - Troubleshooting and support

Содержание Colorado 1630





































































































































































































































































































































































































Результаты поиска

Содержание Colorado 1630

Отзывы:

Бренды по названию

Популярные бренды

Canon Colorado 1630, Руководство по эксплуатации

Результаты поиска

Содержание Colorado 1630

Отзывы:

Бренды по названию

Популярные бренды