Canon Colorado 1630 Скачать руководство пользователя страница 191 | Manualshive

Страница: 191 / 388

Canon Colorado 1630 Скачать руководство пользователя страница 191

Clean the platen

Introduction

When you see pollution on the platen or on the back of your print, immediately clean the platen.

It is advised to clean the platen regularly to keep the printer in the best condition.

Video:

Clean the platen

Before you begin

Use Colorado 1630 prescribed:
• Microflex gloves for handling ink
• Lint free cloths
• Rough lint free cloths
• Cleaning liquid (IPA)
• Compressed air duster
• Micro cleaning brushes (2,5 mm / 0.1 inch)
• Scraper

NOTE

For information on the prescribed maintenance materials, see

List of Colorado 1630

maintenance materials on page 255

.

CAUTION

Wear the prescribed gloves when contact with ink or maintenance materials is possible. Gloves

should always overlap sleeves. Follow the Safety Data Sheets (SDS) guidelines carefully in

order to ensure maximum safety.

CAUTION

Do not use compressed air duster in any way other than described in this procedure.

Procedure

1.

Start the maintenance action via the operator panel. For more information, see

maintenance on page 174

or

Start periodic maintenance on page 176

.

2.

Put on the Colorado 1630 approved gloves.

3.

Open the top cover from the media input side.

4.

If present, remove the media from the paper path. For more information, see

Remove media from

the paper path on page 333

5.

Examine the platen:
• When you see uncured ink on the platen, dab the area with a lint free cloth to avoid rubbing ink

into the suction holes.

• When you see cured ink residue, use a scraper to remove the ink carefully.

Clean the platen

Chapter 6 - Maintain the system

191

«
...
189
190
191
192
193
...
»

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды