background image

18

 

Ten Good Trolling Tips 

1) Test 

your 

lures 

over the boat side before 

sending them down and back. Do this to make 
sure the lure wiggles and wobbles properly 
without going belly up or wandering off. Some 
lures can be adjusted, fine tuned actually, to 
impart maximum action. For example, a slight 
bend in the tail of a spoon or twist of the hook eye 
in the nose of a plug can make a noticeable 
difference in how the lure performs. 
  Also, when running two or more lures, make sure 
the offerings are compatible. Lures that run out of 
harmony with each other are bound to tangle and 
that means wasted time to straighten out the 
mess. Testing them first will avoid the problem. 

 

2)  Consider different sizes

, shapes, and colors 

of lures. No one has ever figured out with 
precision what makes a fish strike or snub a lure. 
There is no doubt, that matching the forage 
(minnows, crayfish, etc.) in color, shape, action, 
and size can help trigger those strikes from 
hungry fish. On the other hand, if fish such as 
bluegills, small mouth bass or Coho salmon are 
protecting spawning beds, they may attack 
whatever is threatening. So, bright colors in lures 
may out produce bland colors. 

 

3) Vary 

trolling 

speeds

. Goosing the engine 

now and then or slowing to a crawl every so often 
will change the action of the lures and may get 
fish to strike them. 

 

4)  Vary trolling patterns and lead lengths

. The 

amount of line you let out often determines how 
deep the lure will run and, to some extent, what 
degree of action it will impart. For starters, 
consider running lures about ten feet behind 
downrigger weights. If flat line trolling, put them 
back about fifty feet, then experiment depending 
on what the fish do. 

 

 

Trolling patterns affect lure action too, that is 

why some anglers like to wheel a lazy S course. 
On turns, outside lures will speed up momentarily 
while inside lures hang for a moment or two. Fish 
may nail lures that change speeds. Also, zigzag 
patterns allow for more water coverage, plus it 
keeps lures out of propeller boil, an important 
consideration for browns and other wary species. 

5)  Locate fish on a vertical plane

. Place lures 

in areas where fish might be. Skilled fishermen 
call these areas the “strike zones”. They include 
the edges of the week beds, structure along 
bottom, drop-offs, preferred temperature of the 
target species, and the thermocline. Remember 
that fish occupy certain areas for certain reasons 
(sources of food, protective cover, preferred 
temperatures, etc.).  

 

6)  Consider special knots and swivels. 

good ball bearing swivel will all but eliminate line 
twist and will aid in getting maximum performance 
from a lure. Many anglers add the tiny swivels to 
split rings already on the lure itself. On the other 
hand, a swivel may dampen the action of a 
sensitive lure, such as a Rapala. Some fisherman 
tie tiny improved cinch or loop knots. Loop knots 
in particular may enhance up and down and side 
to side action of lures. Any good fishing manual 
will explain how to tie these and other knots. 

 

7)  Consider releases for flatline trolling

. A 

good tip is to secure a piece of downrigger cable 
or heavy monofilament to the water ski hook or 
handle below the transom of most boats. To the 
other end of the mono or cable, add a pinch-r-
release. After letting out your lure to the desire 
distance, put the rod in its holder, then bend the 
tip and secure the fishing line in the release. 

 

8)  Add a weed guard

. Having trouble with 

weeds hanging up lures? Consider tying a three-
inch piece of monofilament a foot above the lure. 
Leaves, smaller weeds and other debris may 
catch here momentarily then fall off to the side of 
the lure without tangling. Weedless lures are 
another smart consideration. Downrigger cables 
are effective weed catchers when trolling for pike, 
muskies, or bass in weed-infested lakes. 

 

9)  Add a stinger hook

. When fish short strike, 

slap at lures without becoming hooked, adding a 
stinger hook can solve the problem. Simply tie a 
treble hook to one end of a four inch piece of 
monofilament and then tie the extra hook to the 
last gang of hooks on your lure. The stinger hook, 
which trails the lure, provides extra insurance. 

 

10) Keep hooks sharp

. Some of the best 

fishermen sharpen all hooks after every fish 
caught. Hooks get dull through both use and 
misuse, and probably more fish are lost to dull 
points than anything else. 

TROLLI

NG TIP

S
 

Содержание Mag 20 Dt/Hs





























Отзывы: