Cannon FITZPIBPWR-02-LP, Инструкция пользователя

Страница: 8 / 12

10. THE HEATER MUST BE INSTALLED WITH IT’S INTEGRAL FLUE
CORRECTLY INSTALLED FOR THIS HEATER TO OPERATE
PROPERLY, IF NOT CORRECTLY INSTALLED AND MAINTAINED
VENTING SYSTEM CAN RESULT IN CARBON MONOXIDE (CO)
POISONING AND POSSIBLE DEATH.
11. THE APPLIANCE SHOULD BE INSPECTED PRIOR TO USE,
WITH REGULAR INSPECTIONS (ANNUALLY) TO BE MADE BY A
LICENSED SERVICE PERSON. IT IS IMPORTANT THAT
CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE
KEPT CLEAN, DIRT AND LINT FREE, FOR A SAFE AND
EFFICIENT OPERATION OF THE HEATER.
12. ON THE FIRST LIGHTING YOUR HEATER A SMELL MAY OCCUR
DUE TO IT’S NEW CONDITION. THIS IS NORMAL AND WILL
DISAPPEAR AFTER A FEW HOURS OF USE AT MAXIMUM
CONTROL POSITION.
IMPORTANT.
WHEN THIS HEATER IS OPERATING, THE MESH GUARD IS HOT.
THE MESH GUARD FITTED TO THE HEATER CONFORMS TO
AUSTRALIAN STANDARDS.
FOR PERMENANT PROTECTION OF YOUNG CHILDREN OR THE
INFIRM A SECONDARY GUARD SHOULD BE PLACED AROUND
THE HEATER.
A SECONDARY GUARD IS NOT PROVIDED WITH THIS HEATER
AND MAY BE PURCHASED BY THE OWNER.
STANDARDS.
THIS APPLIANCE MEETS THE FOLLOWING STANDARDS:
STANDARDS AUSTRALIA. AS 3100
AS 5601
AS 4553 / AG 103
Page 2.
SAFETY WARNINGS
7. IF REMOVED THE GLASS WINDOW MUST BE PUT BACK ONTO
THE UNIT PRIOR TO OPERATING THE HEATER.
8. INSTALLATION AND REPAIRS SHOULD BE PERFORMED BY A
LICENSED SERVICE PERSON ONLY, REFER TO BACK OF
MANUAL FOR SERVICE NUMBERS.
9. FOR INSTALLATION INTO A COMBUSTIBLE FIREPLACE
CONSTRUCTED FROM TIMBER OR PLASTERBOARD, THE
FLUE WILL NEED TO BE SUPPORTED TO MAINTAIN
CLEARANCES FROM COMBUSTIBLE MATERIALS.
NOTE: WHEN INSTALLING INTO A MOCK FIREPLACE A MOCK
FIREPLACE INSTALLATION KIT MUST BE USED.
5. NEVER ATTEMPT TO BURN PAPER OR OTHER MATERIAL IN
THE HEATER.
6. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS
APPLIANCE WHILE IT IS IN OPERATION.
DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS
APPLIANCE.
USER INSTRUCTIONS
OPERATING INSTRUCTIONS. 6. TO INCREASE THE FAN SPEED TO HIGH , PRESS SWITCH FOR
HIGH SETTING. REFER FIGURE 6.
7. TO TURN THE BURNER TO LOW SETTING, PRESS SWITCH FOR
LOW SETTING. REFER FIGURE 7.
ON LOW BURNER SETTING IT IS MORE EFFICIENT TO OPERATE
THE FAN SPEED ON LOW.
8. IF THE BURNER FAILS TO IGNITE, WAIT 20 SECONDS AND
REPEAT THE IGNITION PROCEDURE. REFER FIGURE 7.
PRESS PRESS
FIG 6.
FIG 7.
FIG 8.
TO TURN
BURNER
OFF.
TO TURN
BURNER
ON.
Page 5.
NOTE:
IF YOU TURN THE HEATER OFF, WAIT 10 MINUTES BEFORE YOU
TURN THE HEATER BACK ON AGAIN.
THIS WILL ALLOW THE SWITCH WHICH CONTROLS THE IGNITION
TIME TO RESET.
DO NOT USE THIS HEATER IF THE GLASS IS CRACKED OR WITH
THE GLASS REMOVED.
DO NOT USE HEATER WITH BROKEN OR MISSING LOGS.
THE HEATER FLAME SHOULD BE STABLE, NO LIFTING FROM THE
BURNER AND THE LOGS SHOULD GLOW AFTER APPROXIMATELY
15 MINUTES OPERATION ON HIGH SETTING.
THE HEATER IS A FUEL EFFECT UNIT AND IS DESIGNED TO
OPERATE WITH LUMINOUS FLAMES AND MAY EXHIBIT SLIGHT
CARBON DEPOSIT ON THE LOGS. IF ANY EXCESS CARBON
BUILD UP ON LOGS OR THE BURNER FLAME IS UNSTABLE,
CONTACT SAMPFORD AND STAFF IN YOUR STATE.
(SEE PHONE CONTACT PAGE 9.)