Cannon CT-500 Скачать руководство пользователя

Страница: 34 / 49

CT-500 Instruction Manual

Verifying Limit Control Operation

The Limit Control should be checked periodically to ensure its functionality. To check the Limit
Control, follow the procedure below in this section.

Power on the CT-500 and set the instrument to a desired bath temperature. Wait for the bath to
stabilize at the desired temperature.

Using a screwdriver, slowly turn the Limit Control counter-clockwise until the Limit Control OVER
TEMP warning lights up.

Caution:

If the Limit Control fails to light up and the Limit Control has been

adjusted counter-clockwise to its furthest setting, the unit may need repairs.
Contact CANNON for assistance.

When the Limit Control OVER TEMP warning lights up, turn the Limit Control clockwise for ¼
turn and press the OVER TEMP button to reset the Limit Control for normal operation.

Содержание CT-500


















































Результаты поиска

Содержание CT-500

Отзывы:

Похожие инструкции для CT-500

Бренды по названию

Популярные бренды

Cannon CT-500, Инструкция по эксплуатации

Результаты поиска

Содержание CT-500

Отзывы:

Похожие инструкции для CT-500

Бренды по названию

Популярные бренды