- 20 -
C
= SPEED I
D
= SPEED II
E
= SPEED III
F
= AUTOMATIC STOP TIMER - 15 minutes
•
By pressing key
F
for two seconds (with the hood
switched off) the “
clean air
” function is activated.
This function switches the appliance on for ten minutes
every hour at the first speed.
As soon as this function is activated the motor starts
up at the first speed for ten minutes, During this time
key
F
and key
C
must flash at the same time.
After ten minutes the motor switches off and the LED of
key
F
remains switched on with a fixed light until the
motor starts up again at the first speed after fifty min-
utes and keys
F
and
C
start to flash again for ten minutes
and so on.
By pressing any key for the exclusion of the hood light
the hood will return immediately to its normal functioning
(e.g. if key D is pressed the “
clean air
” function is deac-
tivated and the motor moves to the 2nd speed straight
away.
By pressing key
B
the function is deactivated).
• Active carbon/grease filter saturation:
- When button
A
flashes at a frequency of
2 seconds
,
the
grease
filters must be cleaned.
- When button
A
flashes at a frequency of
0.5 seconds
,
the
carbon
filters must be replaced.
After the clean filter has been replaced, the electronic
memor y must be reset by pressing button
A
for
approximately
5 seconds
, until the light on the button
stops flashing.
•COMMANDS:
(Fig.9)
MECHANICAL
the key symbols
are explained below:
A
= LIGHT
B
= OFF
C
= SPEED I
D
= SPEED II
E
= SPEED III
G
= MOTOR WORKING indicator
• Replacing halogen light bulbs (Fig. 11).
To replace the halogen light bulbs
B
, remove the glass
pane
C
using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type.
Caution:
do not touch the light bulb with bare hands.
•
Replacing incandescent light bulbs (Fig. 12).
To remove the incandescent light bulb, take out the
grease filters as described in (Fig. 6) and remove the
bulb.
Replace it with a new one of the same type (Fig. 12).
CUSTOMER ASSISTANCE SERVICE
Before contacting the Technical Assistance Service:
If the product does not operate at all, we advise you to:
- check that the plug has been inserted into the power
socket correctly.
If you cannot identify the cause of the operating
anomaly: switch off the appliance (do not subject it to
rough treatment) and contact the Assistance Service.
PRODUCT SERIAL NUMBER. Where can I find it?
It is important that you inform the Assistance Service
of your product code and its serial number (a 16-
character code which begins with the number 3); this
can be found on the guarantee certificate or on the data
plate located inside the appliance.
This will help to avoid wasted journeys being made by
technicians, thereby (and most significantly) saving the
corresponding callout charges.
THE MANUFACTURER DECLINES ALL RESPONSI-
BILITY FOR EVENTUAL DAMAGES CAUSED BY
BREACHING THE ABOVE WARNINGS.
Содержание CMB 60
