background image

XB, HV, HVA, HVAR, ADD, ADDR, DDS, DDP, SXB, SADD  

M0112_NOV 2020

Page 8 of 8

www.CANARM.COM

Canarm Ltd. - Corporate Head Office    

2157 Parkedale Avenue, PO Box 367    Brockville, Ontario   Canada   K6V 5V6 

Tel: (613) 342-5424              Fax: (613) 342-8437               

[email protected]                      

www

.canarm.com 

Wall supply fan with steel control damper, cabinet and back guard

ADDR  & HVAR FANS

Please note for the reversing models ADDR, HVAR, the supplied reversing switch should be wired in accordance 
with the instructions supplied by the manufactures of the switch. 
 
The blade should come to a complete stop before switching direction. Failure to do so may cause damage to the 
motor and/or blade. 
 
For trouble shooting and electrical guidelines, the above instructions apply.

WARRANTY

 

 
CANARM Ltd. warrants every new fan to be free of defects in materials and workmanship, to the extent that, within a period of one 
year from the date of purchase CANARM Ltd. shall either repair or replace at CANARM’s option, and unit or part thereof, returned 
freight prepaid, and found to be defective. 
This warranty does not include any labour or transportation cost incidental to the removal and reinstallation of the unit at the user’s 
premises. 
Components repaired or replaced are warranted through the remainder of the original warranty period only. 
This warranty applies to the original purchaser-user only; it is null and void in case of altercation, accident, abuse, neglect and 
operation not in accordance with instructions. 
 

NOTICE:

 No warranty claims will be honored by CANARM Ltd. unless prior authorization is obtained.

Installation or Product problems? Do not return to store of purchase. 

Contact Canarm Service at 1-800-265-1833 (CANADA)  1-800-267-4427 (U.S.A) 

1-800-567-2513 (EN

FRANÇAIS) Monday to Friday 8:00am - 5:00pm EST

Содержание XB

















Отзывы: