WARRANTY
For service, contact your local retail outlet or distributor. The warranty period shall be 12 months from the purchase date. Proof of
payment is required for warranty validation. In all cases, the warranty shall apply only to defects in workmanship and specifically
exclude any damage caused by overload, short circuit, misuse, act of vandalism, fortuitous events, acts of God, flood, fire, hail or
natural disaster. This warranty becomes invalid should the installation have been made contrary to our instructions.
CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors.
Do not use fan if any part is damaged.
If using expanding foam to insulate, make sure expansion pressure does not damage
the housing. Read and follow all instructions before operating the fan.
Installation or Product problems? Do not return to store of purchase.
Contact Canarm Service at 1-800-265-1833 (CANADA) 1-800-267-4427 (U.S.A.)
Monday to Friday 8:00 - 5:00pm e.s.t.
USA Warehouse
808 Commerce Park Drive
Ogdensburg, New York, USA 13669
TEL: 1-800-267-4427
FAX: 1-800-263-4598
July/05
UTILITY
EXHAUST FANS
INSTALLATION
For the greatest efficiency, mount the fan as high as possible.
Installation is fast and simple. The fan comes fully assembled. A sturdy framed wall opening should be prepared in advance to the
size indicated for your fan in the charts above. Carefully pull the guard off of the fan unit. Carefully pull the orifice plate off of the fan
unit. Insert the fan unit into the frame. Using wood screws for wooden frames or nut, bolt and lock washers for steel frames, secure
the fan using the mounting holes provided. The shutters should be situated to close by gravity (The shutters will open up and out
when the fan is running and will close by gravity when the fan is stopped). Carefully replace the orifice plate and then the guard
(these should snap back into place). Plug the fan into a 120 volt household outlet. Use the pull chain to turn the fan on and off.
CLEANING
WARNING: Unplug the fan from electrical supply source before cleaning.
After servicing, all safety devices (including grilles and blades) must be reinstalled or remounted as previously installed. Use a soft,
damp cloth, then wipe with dry cloth. Do not use harmful cleaners. Do not bend the blades.
Corporate Office
2157 Parkedale Ave.
Brockville, Ontario, Canada, K6V 5V6
TEL: (613) 342-5424
FAX: 1-800-263-4598
Montreal Distribution Centre
8500 Rue Grenache
Anjou, Quebec, Canada H1J 2B1
TEL: (514) 353-2255
FAX: (514) 353-2522
Arthur Manufacturing Facility
#7686 Concession 16, RR 4
Arthur, Ontario, Canada, N0G 1A0
TEL: (519) 848-3910
FAX: (519) 848-3948
Toronto Manufacturing Facility
130 Claireville Drive,
Toronto, Ontario M9W 5Y3
TEL: (416) 675-4700
FAX: (416) 675-4707
FRAME
FRAMING
10“ (250 mm) X 10“ (250 mm)
12“ (295 mm) X 12“ (295 mm)
FAN SIZE
8”
10”
UF08-W
UF10-G
SHUTTERS
GUARD
FAN
NOTE
1. The guard side of this fan should be mounted indoors and should not be exposed to splashing water.
2. This fan should not be used to exhaust excessive moisture.
3. This fan is for wall mount only, never install this fan in the ceiling.
4. This fan should not be used to exhaust a cooking area or installed near or above cooking equipment.
READ AND SAVE THESE INSTRUCTIONS
WARNING!
Power must be turned off before wiring.
ORIFICE PLATE
