K I N G S T O N
K I N G S T O N
(6)
(7)
Pre-Delivery Information
Before delivery check your spa
height and width and add 5cm
clearance on each side to ensure
access.
X
Check that the hot tub can
clear a 90
°
turn
Rotary Isolation Switch
(pictured). Make sure you have
a qualified electrician prepare
the electrics. Allow 5 metre
slack to connect to Spa.
Ensure you have prepared
a level concrete base or a
properly fitted existing patio or
decking with access to a drain.
Access:
Canadian Spa hot tubs are usually delivered on a flat
bed trailer, up to 5 metres long, 2.4 metres wide and 3.5
metres high. Please ensure that there is adequate access for
such a vehicle to reach your property. When off loading from
our vehicle to the spa site, a minimum of 1100mm width is
required, (some models vary) this also needs to be flat and a
minimum clear vertical height of 9ft should be considered also.
Electrical supply:
If you are having your spa installed, it will
be necessary to have a dedicated electrical circuit supply
fitted. You will require up to 32 Amp (type C Breaker) supply,
dependent on the length from the service point. Your spa must
be protected via a RCD and suitable over current protection.
A minimum of 5 metres of cable is required for connection into
your spa from the Isolator.
Electrical installation:
Arrange for a licensed electrician run
the required 230-volt power line to the spa installation site.
This power line must be permanently connected (hard-wired)
to the mains supply. Do not use extension cords or plug-in type
connections. At the site where the spa is to be located leave 5
metres of cable and the appropriate cable gland. All electrical
wiring to a spa must be installed by a qualified, licensed
electrician, and meet required electrical standards.
Water:
The best means of filling your spa is with a garden
hosepipe (use cold water not hot water). Please ensure that
you have one readily available. If you are aware that your water
pressure is poor, we should be advised prior to delivery. The
design of our spas allows for easy drainage, again, using the
hosepipe which conveniently fits onto the drain valve situated
at the base of your spa. Ideally, you should empty the water to
a nearby drain. You may wish to purchase a suitable
submersible pump to speed up this process.
Decking around your spa:
Ensure that you are aware of the
above measurements. Always consider during your planning
that any decking boards and supporting beams that you install
allow access to the sides of your Spa. It is the customers’
responsibility to ensure that any decking is clear of these areas
prior to any visit by our technicians (Allow 1 metre clearance
around your hot tub and if you have decking ensure part of
your decking can be removed in order to gain access for future
repair or servicing). If you are unsure then please ask before
ground construction and the delivery of your spa.
Your spa must be sited on a solid, flat, level base which is the
same size or larger than the spa. The base can be either a
10-15cm concrete slab or suitably strengthened timber
decking or existing patio area assuming it has suitable
foundations of hardcore. Whatever base area is chosen, it must
be of suitable load bearing capacity. Please ensure your base
has suitable drainage.
NOTE: A 10-15 cm concrete base is ideal preparation for a hot tub.
Ensure part of your decking can be removed in order to gain access for future
repair or servicing
Optional CraneService is available
How to change the Black Ice UV Lamp & Tube
To replace UV Light Lamp Only
Remove pressure fit end and replace Lamp. The end of the Lamp has 4 pins that fit
into 4 pin plug, there will be no water as the clear quartz tube is sealed in UV
Chamber, replace end and put back in and turn on valves.
UV Light Water Treatment System
• Input Voltage: AC 230V 50/60 HZ
• Operating Current: 100mA
• Power: 15W
• Purification of water: 15L / Minute
• UV Lamp Lifetime 6000-8000 Hr
• Replace UV Lamp Annually
c a n a d i a n s p a c o m p a n y . c o m
Spa Status LED (Optional)
Our new Spa Status LED provides convenience, right at your finger tips. Check the
status of your spa by looking at the colour of the LED light from afar – no more
breaking your back trying to remove your cover just to see if your spa is running!
NORMAL
OPERATION
REMINDER
NOTIFICATIONS
NEEDS
ASSISTANCE
To replace UV Quartz Glass Tube & UV Light Lamp.
Follow UV Lamp replacement but before installing new UV Lamp unscrew end off UV
Chamber and you will find a Quartz glass tube and a ‘O’ ring - replace tube and put ‘O’
ring near the top of the Tube, insert into chamber and screw back metal end, then install
new UV Lamp. (Make sure to use gloves).
IMPORTANT:
1) Turn off the power.
2) Allow the UV Lamp to cool before replacing.
3) Do not look at lit Lamps to avoid eye damage.
Step 1:
Turn both red vales off horizontal position
(as photos below) to isolate the UV Silver chamber.
UV Quartz Glass Tube & ‘O’ ring
UV 15w Lamp & Gloves
Black Ice UV Kit
KK-11216
Step 1:
Unscrew the 2
red-marked screws.
Step 2:
Remove the red lid
Step 3:
Unplug this white
connector
Step 4:
Take out this black
protective sleeve
Step 5:
Pull out the Lamp to
change it
Step 6:
Put the Lamp inside
the metal tube and cover it
with black protective sleeve
Step 7:
Plug in the white
connector
Step 8:
Cover the red lid and
install these 2 screws
How to change Canadian Spa Wave Zone Lamp
IMPORTANT:
1) Turn off the power. 2) Allow the UV Lamp to cool before replacing.
3) Do not look at a lit UV Lamp to avoid eye damage.
Wave Zone UV Lamp Kit
KK-11202
The Advanced Oxidation Process is used
in Canadian Spa Company's Hot Tubs.
Combining our Ozone Generator with Ultra
Violet Light creates a unique bacteria
fighting superhero: Super Hydroxyl
Radicals. They easily overcome even the
most powerful of bacteria.
Turn both red vales off horizontal position
(see photos opposite) to SHUT OFF the
water and isolate the UV chamber.
ON
OFF
