manualshive.com logo in svg

Canadian Solar Dymond CS6K-245M-FG, Руководство по установке

Поделиться
Скачать
Canadian Solar Dymond CS6K-245M-FG Скачать руководство пользователя страница 8

EN-Rev IM-FDM-EN/1.6 Copyright © March 2017. Canadian Solar Inc.

8 | 

CORRECT WIRING SCHEME 

 

·  Ensure that the wiring is correct before starting up the 

system. If the measured open circuit voltage (Voc) and 
short-circuit current (Isc) differ from the specifications, 
this indicates that there is a wiring fault.  

 

CORRECT CONNECTION OF PLUG CONNECTORS

  

·  Make sure that connections are safe and tight. 

Plug connector should not be subjected to stress 
from the exterior. Connectors should only be  
used to connect the circuit. They should never  
be used to turn the circuit on and off.  

USE OF SUITABLE MATERIALS  

·  Only use dedicated solar cable and suitable plugs 

(wiring should be sheathed in a sunlight-resistant 
conduit or, if exposed, should itself be sunlight- 
resistant) that meet local fire, building and electrical 
regulations. Please ensure that all wiring is in  
perfect electrical and mechanical condition.  

·  Installers may only use 2.5-10 mm

2

 (8-14 AWG) 

single conductor cable listed and labeled as PV Wire 
or TUV 2PfG1169 approved, that is 90°C wet rated 
with proper insulation that is able to withstand the 
maximum possible system open-circuit voltage. 
Only copper conductor material should be used. 
Select a suitable conductor gauge to minimize 
voltage drop and ensure that the conductor 
ampacity complies with local regulations (i.e. NEC 
690.8(D)).

CABLE PROTECTION 

 

·  Secure the cables to the mounting system using 

UV-resistant cable ties. Protect exposed cables 
from damage by taking appropriate precautions 
(e.g. placing them inside a plastic conduit). Avoid 
exposure to direct sunlight.

·  A minimum bending radius of 60 mm is required 

when securing the junction box cables to the  
racking system.

CONNECTOR PROTECTION 

 

·  Protect exposed connectors from weathering 

damage by taking appropriate precautions. 
Avoid exposure to direct sunlight.

5.2 

MODULE GROUNDING

·  EQUIPMENT GROUNDING: double glass modules 

do not present any exposed conductive parts, and 
therefore do not require to be electrically groun-
ded for compliance to the National Electrical Code.

·  Proper equipment grounding is still required for 

the racking system in compliance with all local 
electrical codes and regulations. Please refer to the 
racking system user instructions.

6.0  

MOUNTING INSTRUCTIONS

STANDARD MODULES

For a clear understanding of our modules, please

refer to the illustration of a module shown below:

The applicable regulations pertaining 
to work safety, accident prevention and 
securing the construction site must be 
observed. Workers and third party

personnel shall wear or install fall arrest equipment. 
Any third party need to be protected against injuries 
and damages.

·  The mounting design must be certified by a regis-

tered professional engineer. The mounting design 
and procedures must comply with local codes and 
requirements from all relevant authorities.

·  Each module must be securely fastened at a 

minimum of 4 points on two opposite sides. 

  Junction box
  Plastic corners 

  Cables and connectors 

 

(-)

(+)

Содержание Dymond CS6K-245M-FG

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды