www.camsat-cctv.com
Full instructions available on the www.camsat-cctv.com
Full instructions available on the www.camsat-cctv.com
First start-up
WARNING
Before any start-up, connect both antennas! Trying to run the machine without screwed antennas may
cause damage to the radio link.
Connecting the power supply of 230V
When using the 230V, connect iCAM-Mobile power plug into the socket adapted to the conditions of
use, ie. external hermetic socket or connector plug enclosed in another hermetic enclosure / box.
Mounting at the installation site / monitored area
Starting at the destination point / monitored
Remote access to the system ICAM-MobileHD
Wireless access to the system
Access to iCAM-MobileHD system with Android or iOS
Recorder
Log in to recorder
WARNING
Kit (iCAM-Mobile with IP camera) should be mounted only to solid, stable construction of walls and poles.
The installer is responsible for proper installation of the camera!
In the selected location you should mount wall bracket adapter with anchors to the wall or pole handle
adapter with steel bands.
Additionally, you should install steel safety cable to a separate anchors or any other part of the pole. Safety
cable must be mounted to a solid, robust construction, which will guarantee the iCAM with the camera will
be hold in case of an emergency.
Slide the camera (antenna up) into the holder, and then attach the safety cable and padlock to secure the
camera or twist two caps on the bolts to prevent unauthorized assembly.
Plug iCAM-Mobile power plugs into the socket adapted to the conditions of use, ie. the outer hermetic
connector or connector plug enclosed in another hermetic enclosure / box.
After turning the ignition key to the "I" it should light up two LEDs on the external panel (STATUS NVR, Power
MAIN). iCAM-MobileHD starts to record the image, and full remote access to the device will be possible.
WARNING
After starting the machine, remove the key from the ignition, leaving it in position "1" to prevent the the
shutdown of the system by third parties.
WARNING
After starting the machine, remove the key from the ignition, leaving it in position "1" to prevent the the
shutdown of the system by third parties.
To complete the setup, connect your PC wirelessly via a WiFi network in the 5 GHz band (802.11a or
802.11n). The default network name (SSID) is "CAMSAT."
Configuration example for iCAM-Receiver is shown below.
Devices operating only in the band 2.4 GHz (802.11b and 802.11g) are incompatible with iCAM-Mobile!
As a receiving device you can use the device iCAM-Receiver (not included in the kit).
You need to connect to a Wi-Fi network using the pre-configured network
name, password (the default SSID: CAMSAT) and configure the IP settings.
If the device did not receive an IP address automatically, during connecting
manually enter a unique static IP address, default gateway, and subnet
mask in the advanced options. The HDCP server must be ON so configura
-
tion was performed automatically, you can turn it on in the settings of the
radio
Link settings → Network Settings (CAMERA CONNECTION SETTINGS
→ Network Settings
).
To log in to the recorder module, launch the web browser Internet
Explorer and enter the IP address of the module (the default address,
assuming 192.168.1.188). Appears on the screen menu login. On the
screen, enter your login information (default: Username: admin,
password: none).
When you use a browser other than Internet Explorer, select "NoN ActiveX."
Install ActiveX plugin (Internet Explorer only!)
Run the installer ActiveX plugin (rtspvideoplugin.exe), and close the IE browser before installing. Once
successfully installed, open your browser again. Enter the IP address of the recorder, and then log on.
When prompted, allow the browser to run plug-ins.
Example configuration
The default settings of the recorder
IP address
192.168.1.188
Subnet mask
255.255.255.0 (CIDR /24)
CMS application port
5050
Mobile devices port
5053
Rtsp stream
554
User name
admin
2
3
Standard
Onvif
IP address
192.168.1.190
Port Onvif
80
User
admin
Password
admin
Password
Feature
Pre-configured IP camera
Factory settings
