
①
Photocell : Sensor for lights
②
Ready : Lighting test, lights up when pressed.
③
Slave : On/off switch for synchro sensor.
- On(Green lamp on) : Operated by synchro
sensor or synchro cord
- Off(Green lamp off) : Operated by synchro
cord only.
④
Alarm : On/off switch for alarm
(checking the charging status)
- On(Green lamp on) : Beeps while being charged,
stops beeping when over.
- Off(Green lamp off) : Resets alarm
⑤
Power : Main power switch
- On (Red lamp on)
- Off (Red lamp off)
⑥
Flash : Controler for output volume (1/8 Minimum - 1/1 Maximum)
⑦
Model : Controler for modeling volume ( Minimum - Maximum)
1. Small, lightweight and reasonable price compared to quality and function.
2. Very convenient to control modeling lamp by stepless slide volume and flash volume by touch button.
3. It easy to insert in & out PCBs.
4. Very suitable for portrait, profile, and digital photographing.
5. Umberella reflector, snoot, honeycomb grid, barn-door, softbox, bags are available for customers convenience.
STATUS
Photo cell does
not operate.
Synchro cord
does not operate.
No operation
Others
Slave off.
Check whether cell is on or not.
Change the position of flash so that light can reach
the photo cell
Isolate the flash from very strong light.
The light does not reach photo cell.
Too much light shines photo cell.
Dust or stain on the synchro cord jack
Remove dust or stain
Replace it (Check whether it turns on or not by pressing
test button)
Shortened synchro cord or bad connection
- Check if the electricity cord is well inserted.
- Check if the contact of consent is OK.
- Check the fuse.
No electricity
Please consult A/S center or manufacturer. They will provide you safety, insure proper operational
functions and provide continuation of your warranty.
※
This product can be modified for better quality and function without prior notice.
741-1 Sangyeck-dong, Buk-gu, Korea / www.alb.co.kr / e-mail : [email protected]
Tel : +82 53 384 9874 / Fax : +82 53 384 9886 / For product consulting, call us :+82 53 384 9870
1. How to replace modeling lamp(BASE:E-11 or E-27)
- Cool off and then take out the modeling lamp.
- Be careful not to leave fingerprints or stains on the lamp, clean up the surface of lamp after replacement.
2. How to replace a fuse
- First take out the electricity cord.
- Disassemble fuse holder and take out the fuse.
- Check the fuse is short and replace it with a spare fuse in the fuse holder.
3. How to keep flashes
- Protect pirex dome and xenon tube from dust or stain while being kept
- If there are dust or stain on the pirex dome or xenon tube which lifetime might be shortened or lead lower
color temperature, clean up them with soft fabric.
※
Remarks : It might not recharge fully when a rated voltage is higher than input voltage.
In this case, please check input voltage.
This product can be modified for better quality without prior notice.
3. Functions of Control Panel
1. All powers are lowered and lighting volume is
minimised when the flash was released from the
factory.
2. Check the modeling lamp volume, flash volume,
and the power is turned off before power on.
3. Connect synchro cord to the synchro socket.
4. Turn on power button(Red lamp on).
5. Never forget to discharge the remaining electric
currency before turns off the mail power.
5. Operation
6. Characteristics of Camray
8. Trouble Shooting
7. Maintenance
1
3
4
5
6
7
2
4. Specification
Subject
300W/s
AC 220V 50/60Hz
1/700~1/1,600sec
0.5~2.0sec
Halogen : 100W
26
×
16
×
10cm
1.6kg
Synchro cord, Slave, Test button, IR
Titanium, Aluminium
Stepless volume control (50~300W/s)
Stepless volume control (25~100%)
5500
±
100 K
±
0.1%
ON/OFF switch
ON/OFF switch
DC 12V
Standard reflector, modeling lamp, synchro cord
Snoot, spot, softbox, umbrella, barn-door,
honeycomb grid, bag
C-300
ESTIMATED CAUSE
TROUBLE SHOOTING
Items attached
Options
Triggering voltage
Max. Output
Input voltage
Recharging time
Flash Duration
Color Temperature
Modeling lamp
Triggering method
Working voltage
Modeling lamp voltage
Output tolerance
Synchro
Alarm
Chasis
Size
Weight
4
3