Campo Equipment ECOBlaze DF1600 Скачать руководство пользователя страница 13

Страница: 13 / 19

CAMPO EQUIPMENT CO. LTD. (ECOBLAZE)

6 Carson Court, Brampton, ON, CANADA, L6T 4P8

Tel: (905) 793-2525 | Fax: (905) 793-8768 |

www.campoequipment.com

pg. 13

TROUBLESHOOTING

NOTE:

Before replacing any component, test according to instructions in this manual. This

trouble shooting guide will say replace, but replacement should occur only after appropriate
testing.

TROUBLESHOOTING DF1600 DIRECT FIRED HEATER

PROBLEM

CONDITION

REMEDY

Blower Motor does not
run. (Blower mode)

1. No current to heater.

1. Turn breaker

– safety switch

ON.

2. Voltage insufficient

2. Check incoming supply.

3. Wiring

– connections

disconnected

– loose –

broken.

3. Connect

– tighten – replace

wiring connections.

4. Main Switch OFF

– Defective. 4. Turn Control toggle Switch

– replace Switch.

5. Defective VFD.

5. Check to see if there is power

to the VFD.

Burner does not ignite.

1. Voltage insufficient.

1. Check incoming supply.

2. Electrode

– disconnected –

adjusted incorrectly

–

defective.

2. Connect

– adjust - replace

electrode.

3. Air Proving Sw.

Disconnected

– defective.

3. Connect

– Replace Air

Proving Sw.

4.Tilt switch Disconnected, or

Unit is not on a level surface or
defective.

4. Connect

—Replace Tilt Switch

or Level the Unit.

5.Fan Over heat switch is open.

5. Check to see if the unit is not

running on low voltage or fan
is not over heating.

6. Insufficient Gas delivery.

6. Fill tank

– open valves –

replace solenoid valves.

7. Regulators adjusted incorrectly

– defective.

7. Adjust

– replace regulators.

8. Burner gas ports

– obstructed

– damaged.

8. Clean ports

– replace burner.

9. Flame sensor

– damaged –

defective.

9. Replace Flame Sensor.

Burner stops during
usage.

1. Heater overheating.

1. Check to see if modulating
valve is not stuck.

2. Power interrupted.

2. Restore power.

3. Gas Burner ports obstructed.

3. Clean

– replace burner.

Содержание ECOBlaze DF1600




















Результаты поиска

Содержание ECOBlaze DF1600

Отзывы:

Похожие инструкции для ECOBlaze DF1600

Бренды по названию

Популярные бренды

Campo Equipment ECOBlaze DF1600, Руководство пользователя

Результаты поиска

Содержание ECOBlaze DF1600

Отзывы:

Похожие инструкции для ECOBlaze DF1600

Бренды по названию

Популярные бренды