Campbell OBS501 Скачать руководство пользователя | Manualshive

Страница: 37 / 66

background image

OBS501 Smart Turbidity Meter with ClearSensor

®

Technology

27

5.

Wipe sensor with a clean, dry towel to remove residual standard.

6.

Repeat steps 2, 3, 4, and 5 for the other standards.

7.

Perform 2

nd

-order polynomial regressions on the calibration data to get the

coefficients for converting OBS signals to TU values.

FIGURE 8-4. OBS501 in 500-TU AMCO Clear

®

turbidity standard in

100-mm black polyethylene calibration cup

8.6.2 Sediment

There are three basic ways to calibrate an OBS sensor with sediment. These are
described in the following sections. However, only the procedures for dry-
sediment are explained in this manual. Typically, the sensor will record in
turbidity units and the relationship to suspended-sediment concentration is
calculated in a spread sheet or database after the data is retrieved to a computer.

8.6.2.1 Dry-Sediment Calibration

Dry-sediment calibration is a calibration performed with sediment that has
been dried, crushed, and turned to powder. This is the easiest calibration to do
because the amount of sediment can be determined accurately with an
electronic balance and the volume of water in which it is suspended can be
accurately measured with volumetric glassware. Of the three methods, dry-
sediment calibration causes the greatest physical and chemical alteration of the
sediment. Alteration of the sediment size as a result of processing can
significantly affect the calibration slope. FIGURE

Normalized response of

OBS501 to AMCO Clear

(p. 24)

, shows, for example, that reducing the

grain size by a factor of two during grinding can increase OBS sensitivity by a
factor of two.

«
...
35
36
37
38
39
...
»

Содержание OBS501



































































Отзывы:

Нет отзывов

Похожие инструкции для OBS501

Бренд: Samson Страницы: 4

Бренд: Kane Страницы: 12

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: Omer Страницы: 2

Бренд: QMI Страницы: 54

Бренд: Dewetron Страницы: 24

Бренд: HBM Страницы: 84

Бренд: Dakota Digital Страницы: 38

Бренд: Swema Страницы: 4

Бренд: PASI Страницы: 59

Бренд: Lutron Electronics Страницы: 10

Бренд: Michell Instruments Страницы: 28

Бренд: 3nh Страницы: 39

Бренд: A-CUBE Страницы: 25

Бренд: Chauvin Arnoux Страницы: 64

1101-3121-0049-800

Бренд: S+S Regeltechnik Страницы: 16

GRAND RHAPSODY PIANO

Бренд: Waves Страницы: 19

WTW SensoLyt 900

Бренд: Xylem Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды