Campbell NL241 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 76

background image

Appendix A. Cables, pinouts,
LED function, and jumper

A.1 CS I/O

The CS I/O cable is a 9-pin, straight-through cable with all 9 pins connected. The supplied SC12
cable is recommended. Pin configuration for the CS I/O port and connected peripheral device is
shown in the following Table.

Table A-1: CS I/O pinout

Pin

Data logger (DB9 female)

function

Peripheral (DB9 male)

function

1

5 VDC

N/C

2

SIGNAL GND

SIGNAL GND

3

RING

RING

4

RXD

TXD

5

ME

ME

6

SDE

SDE

7

CLK/HS

CLK/HS

8

12 VDC (output)

12 VDC (input)

9

TXD

RXD

A.2 RS-232

A DB9 female to DB9 male cable is used to connect the NL241 RS-232 port to the data logger
RS-232 port. The supplied SC12 cable can also be used. A DB9 female null modem cable is used
to connect the NL241 RS-232 port to a computer RS-232 port. The RS-232 cable should be kept
short when using high baud rates. Pin configurations for the RS-232 port of a data logger and
peripheral device are shown in the following Table.

NL241 Wireless Network Link Interface

42

«
...
46
47
48
49
50
...
»

Содержание NL241













































































Отзывы:

Нет отзывов

Похожие инструкции для NL241

Бренд: Campbell Страницы: 18

Бренд: Vector Страницы: 4

Бренд: Omnia Страницы: 8

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: Zennio Страницы: 3

Бренд: JBM Страницы: 13

Бренд: Masterclock Страницы: 19

SeQual Eclipse 5

Бренд: CAIRE Страницы: 2

Бренд: Eleiko Страницы: 4

Бренд: Heiniger Страницы: 164

Бренд: Hausmann Страницы: 10

BOMAG BW 120 AD-5

Бренд: Fayat Страницы: 210

Levitator III F-LHLEV3

Бренд: Skytron Страницы: 248

Бренд: Viavi Страницы: 404

Бренд: Frick Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды