Campbell AL205E Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 36

Campbell AL205E Скачать руководство пользователя страница 8

10. If revisions are needed, press Enter twice within 5 seconds. This will re-enter the process

and allow the user to make changes. After 5 seconds without pressing Enter, the AL205E
stores the new settings and then starts to operate.

3.1 Settings explanations

The following tables show the AL205E settings (numbered 0 through 55) and their default values.
Press Enter or wait about three seconds to move to the next setting. More detailed explanations
of these settings can be found in Chapter 2 of the ALERT2 API Specification 1.0 document found
at

https://s.campbellsci.com/documents/us/miscellaneous/alert2-intelligent-network-device.pdf

.

Table 3-1: Settings

Setting

number

Setting

Description

[00/55]

Start serial boot
loader to load new
program?

To load a new operating system into the AL205E, type 1 then
press Enter to put the AL205E into boot loader mode (see

Operating system update

[01/55]

Load default
configuration
parameters & save
in non-volatile
memory?

Type 1 then press Enter to reset the device to factory defaults
and load the default settings in the flash memory.

[02/55]

Enable test
ransmissions?

Type 1 or 2 to put the AL205E in the test mode, which causes
the AL205E and radio to generate a tone. Type 3 to force the
AL205E to send an ALERT2 transmission. See

transmission procedure

(p. 17) for more information.

1 = continuous 1 KHz audio tone

2 = continuous 1.2 KHz audio tone

3 = ALERT2 transmission

AL205E ALERT2 Encoder

6

«
...
6
7
8
9
10
...
»

Содержание AL205E





































Отзывы:

Нет отзывов