background image

Page 

7

 - Manual 

FA01321 -

EN

 - 03/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - T

ranslation of the 

original instructions

GENERAL INSTRUCTIONS FOR INSTALLING

 Only skilled, qualified staff must install this product in full compliance with the law in force.

 If the door is fitted with a pedestrian door, you must also fit a safety switch at the entrance, to stop the 

operator from working when the pedestrian door is open.

Preliminary checks

 Before beginning the installation, do the following:

• 

make sure you have set up a suitable dual pole cut off device along the power supply that is compliant with the 
installation rules. It should completely cut off the power supply according to category III surcharge conditions 
(that is, with minimum contact openings of 3 mm);

• 

Set up suitable tubes and conduits for the electric cables to pass through, making sure they are protected 
from any mechanical damage;

• 

 make sure that any connections inside the container (ones that ensure continuity to the protection circuit) 

are fitted with additional insulation with respect to those of other electrical parts inside;

• 

make sure that the door is properly balanced. When stopped at any point, it must maintain its position.

Slide guides

001

V06001

Chain guide L = 3.02 m.
Counter-balanced overhead doors up to 2.4 m in height
- Counter-balanced overhead doors up to 2.25 m in height
- Sectional* doors up to 2.20 m in height.

001

V06002

Chain guide L = 3.52 m.
- Counter-balanced overhead doors up to 2.75 m in height.
- Sectional* doors up to 2.70 m in height.

001

V06003

Chain guide L = 4.02 m.
- Spring-balanced overhead doors up to 3.25 m in height.
- Sectional* doors up to 3.20 m in height.

001

V06005

Belt guide L = 3.02 m.
Counter-balanced overhead doors up to 2.4 m in height
- Counter-balanced overhead doors up to 2.25 m in height
- Sectional* doors up to 2.20 m in height.

001

001

V06006

Belt guide L = 3.52 m.
- Counter-balanced overhead doors up to 2.75 m in height.
- Sectional* doors up to 2.70 m in height.

001

V06007

Belt guide L = 4.02 m.
- Spring-balanced overhead doors up to 3.25 m in height
- Sectional* doors up to 3.20 m in height.

Page 

7

 - Manual 

FA01321 -

EN

 - 03/2019 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. -  Original instructi

ons

Содержание V1000P





























Отзывы: