CAMBRIDGE CSW-10AT-B Скачать руководство пользователя

Страница: 15 / 17

.1 Testing

Menu Definitions

Version Displays Software Version.

Display

Lights all display segments and indicating LED s

Buttons Press the Zero key, b1 will be displayed.

Press the GRS/NET key, b2 will be displayed.

Press the Tare key, b3 will be displayed.
Press the lb/kg key, b4 will be displayed.
Pressing the print key will exit back to the menu T3.

A to D

Displays Raw counts where a 1mV/V signal from the scale

will display 25,000 counts.

When in angle mode Down GRS/NET will cycle Pitch, Roll
and Raw counts.

Serial

Serial communications can be verified by connecting pins
2 and 3 on the serial port. A single character will be echoed

and pass or fail will be displayed.

Setup data

Setup data will be sent out on the printer port.

Default

Resets the meter back to factory defaults clearing all

calibration and setup data. "r you sure?" will be displayed

then press the Tare key to exit without Defaulting, or press

the Print key to reset the meter to factory default.

END

Exits back to the main Menu.

.0 TESTING PROCEDURES

CAMBRIDGE SCALE WORKS, INC.

Manual P/N 5999-1011-02

Содержание CSW-10AT-B


















Результаты поиска

Содержание CSW-10AT-B

Отзывы:

Похожие инструкции для CSW-10AT-B

Бренды по названию

Популярные бренды

CAMBRIDGE CSW-10AT-B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CSW-10AT-B

Отзывы:

Похожие инструкции для CSW-10AT-B

Бренды по названию

Популярные бренды