background image

3

SPEAKER PLACEMENT

The proper placement of speakers affects how well the AV

surround system recreates the soundfield intended by the

recording engineer. Current recording practice typically

assumes a speaker array with a center channel speaker

directly in front of the central viewing position. Left and right

speakers are placed so they each form a 30 degree angle

from the centerline. Left and right surround speakers should

be 110 degrees from the centerline. Left and right rear

speakers in a 7.1 system should be at 140 degrees. If a sin-

gle rear speaker is used in a 6.1 system, it should be cen-

tered on the rear wall. Front speakers should be as close to

the height of the TV monitor as practical. Surround and rear

speakers should be slightly higher. Recreate this speaker

pattern as closely as your room and furnishings allow.

Don’t be too concerned if your situation and listening envi-

ronment dictate the speakers’ position. Most rooms do not

allow ideal placement. Place your speakers as close to

these guidelines as practical. The speakers will still provide

convincing, lifelike sound.

Your surround processor has a variety of adjustments to

optimize the sound based on the speakers’ capabilities and

placement. These adjustments vary by processor, so refer

to your processor’s manual for instructions specific to your

equipment. Set your main, center, and surround settings to

“SMALL”, with subwoofer “ON”. If your processor allows you

to adjust the crossover frequency, set it as close to 100Hz

as possible.

• Avoid placing front left and right speakers very close to a

side wall (within 12-14 inches). The reflected sound from the

wall degrades the sound coming directly from the speaker.

RECOMMENDED DISTANCE

APART FOR STEREO

20 - 55

ANGLE

APPROX.

EAR LEVEL 

MAXIMUM RECOMMENDED DISTANCE

APART FOR HOME THEATER

SURROUND

SPEAKER

SURROUND

SPEAKER

POWERED 

SUBWOOFER

CENTER CHANNEL

MAIN SPEAKERS

LEVEL 

WITH

CENTER

SPEAKER

1

4

0

º

1

4

0

º

11

11

30º

30º

7.1 REAR

SPEAKER

7.1 REAR

SPEAKER

MAIN

SPEAKER

MAIN

SPEAKER

Содержание NEWTON MC650HD













Отзывы: