Cambium Networks PMP 450 Series Скачать руководство пользователя

Страница: 78 / 292

Chapter 2: System hardware

Table 48 :-48 V DC Power Injector interfaces

Interface

Function

DC input

36 to 60 V, 2 A

RJ45 Sockets

Two (Data In and Data & Power Out)

LEDs

Two (AC and Port)

Pow er sup p ly – PMP/ PTP 4 50 b Ser ies

The PMP/PTP 450b Series support powering from the following powering sources:

Gigabit Ethernet Capable Power Supply – 20 to 32 V DC, 15 W

CMM4 with external 29 V power supply

CMM5 29 V power and sync injector module with external 240 W or 600 W power supply

Figure 19 :

-20 to 32 V DC Power Injector interfaces

Содержание PMP 450 Series





































































































































































































































































































Результаты поиска

Содержание PMP 450 Series

Отзывы:

Похожие инструкции для PMP 450 Series

Бренды по названию

Популярные бренды

Cambium Networks PMP 450 Series, Руководство по установке

Результаты поиска

Содержание PMP 450 Series

Отзывы:

Похожие инструкции для PMP 450 Series

Бренды по названию

Популярные бренды