Calsense CS3000 страница 16 Скачать руководство пользователя

Страница: 16 / 85

CS3000 User’s Guide

Calsense

Device Compatibility

2-Wire Decoders

Calsense 2-Wire technology provides easy and cost-effective installation and built-in robust lightning

and surge protection, making it durable and reliable. Decoders not only receive commands from the

controller but also send real-time information back. Diagnostic information is gathered automatically

from each decoder on a continual, real-time basis and recorded and transmitted back to the controller

as well as the Command Center Online cloud application.

2-Station 2-Wire Decoder

The Calsense 2-Station 2-Wire decoder (model CS-2W-2ST) operates up to 2-solenoids using uniquely

colored wires for each station (Figure 6). A single controller can operate up to 128 2-Wire stations,

spread across a maximum of 70 physical 2-Station decoders.

Figure 6: 2 Station 2-Wire Decoders

Содержание CS3000






















































































Результаты поиска

Содержание CS3000

Отзывы:

Похожие инструкции для CS3000

Бренды по названию

Популярные бренды

Calsense CS3000, Руководство пользователя

Результаты поиска

Содержание CS3000

Отзывы:

Похожие инструкции для CS3000

Бренды по названию

Популярные бренды