![background image](http://html1.mh-extra.com/html/calrec/type-r/type-r_installation-manual_3515809016.webp)
1. In
CoreConfigure
, navigate to the
ControlSurfaces
page. See above right.
2. Select
MixerA–SurfaceA
.
The surface may now be renamed using
the text entry field at the top of the screen.
3. To add a fader panel select
Addfader
panel
. This will open the
Addfader
panel
dialogue. See middle right.
4. Set the type to
Faderpanel
.
Note:
If you do not have a fader panel,
select
Virtualpanel
.
5. Set the
PanelID
to match the switches
on the rear of the panel.
Tip:
Use the Panel ID switch tool in the
UI to match the switches on the rear of
the panel. Also see
“SurfacePanels-SuggestedSettings”
for recommended Panel ID’s.
6. Set the fader range to
1–6
then click
Add.
7. Continue to add fader panels in the same way, with unique panel
IDs and fader range values, until all required fader panels are
added to the surface layout.
8. To add a Soft Panel select
Addancillarypanel
. This will
open the
Addancillarypanel
dialogue. See below right.
Note:
Where there are multiple fader panels, multiple
Add
ancillarypanel
buttons will be available. This is to allow you
to position the panel in the surface layout in a way that roughly
matches your intended surface setup and will also facilitate the
creation of user sections later. The position chosen does not
determine the functionality available to the soft panel.
Up to 8 soft panels may be added per fader section, up to a
maximum of 26 soft panels per core system.
9. Select the type of panel,
LSP
or
SSP.
10. Set the
PanelID
to match the switches on the rear of the panel.
Tip:
Use the Panel ID switch tool in the UI to match the switches
on the rear of the panel.
11. Give the panel a label (e.g. LSP 1, SSP 1, Guest 1), then click
AddPanel
.
12. When all surface panels are added to the layout, click
Save
in
the footer of the control surfaces page.
13. Restart the core from the reset button on the front of the core for
the changes to take effect.
CORE CONFIGURE CONTROL SURFACES PAGE
ADD FADER PANEL DIALOGUE PAGE
ADD ANCILLARY PANEL DIALOGUE PAGE
4. CONFIGURE THE CORE FOR SURFACE PANELS
Содержание TYPE R
