background image

GB

Page 

6

CT,T, TP,  Rev22 - Operating Instructions

  It is forbidden to execute any operations with 

the direct use of hands. Use water-resistant, 

anti-cut gloves to disassemble and clean or in 

other particular cases.

i

 

 

During maintenance operations external

personnel is not allowed.

Maintenance operations that are not described in 

this manual must be made only by special personnel 

authorized by Calpeda S.p.A.

For further technical information regarding the use or 

the maintenance of the device, contact Calpeda S.p.A.

8.1. Routine maintenance

OFF

 

 

Before every maintenance operations 

disconnect the power supply and make sure 

that the device could not accidentally operate.

When the pump remains inactive it must be 

emptied completely if there is a risk of freezing.

Remove the front cover (12.00) or the drain plug 

(14.12), if available, to empty the pumps

of the T, TP series. To empty completely the CT pumps, 

remove the pump and turn it upside-down.

After a long idle period, before restarting the unit, 

check that the impeller is not jammed because of 

incrustations, settling solids (deposit formation) 

or other causes. If necessary clean with suitable 

action.

8.2. Dismantling the system

Close the suction and delivery gate valves and drain 

the pump casing before dismantling the pump.

8.3. Dismantling the pump

OFF

Close the suction and delivery gate valves before 

dismantling.

For dismantling and re-assembly see construction in 

the cross section drawing.

To remove the impeller (28.00) T, TP use the threaded 

dismantling holes.

9. DISPOSAL

OFF

The  final  disposal  of  the  device  must  be  done  by 

specialized company.

Make sure the specialized company follows the 

classification of the material parts for the separation. 

Observe the local regulations and dispose the device 

accordingly with the international rules for environment 

protection.

10.

 

SPARE PARTS

10.1. 

Spare-parts request

When  ordering  spare  parts,  please  quote  their 

designation, position number in the cross section 

drawing and rated data from the pump name plate 

(type, date and serial number).

The spare parts request shall be sent to CALPEDA 

S.p.A. by phone, fax, e-mail.

11.

  D

ESIGNATION OF PARTS

Nr. Designation

12.00 Casing cover

12.20 Screw

14.00 Pump casing

14.04 Plug (filling)

14.12 Plug (draining)

14.20 O-ring

14.24 Screw

28.00 Impeller

28.20 Impeller key

32.00 Lantern bracket

36.00 Mechanical seal

36.50 Shoulder ring

36.52 Shoulder ring

46.00 Deflector

70.00 Lantern bracket

70.18 Screw

73.00 Pump-side bearing

73.12 Circlip

76.00 Motor casing with winding

76.04 Cable gland

76.16 Support

76.54 Terminal box, set

78.00 Shaft with rotor packet

81.00 Fan-side bearing

81.08 Circlip

82.00 Motor end shield, fan side

82.04 Compensating spring

82.08 Screw

88.00 Motor fan

90.00 Fan cover

90.04 Screw

92.00 Tie-bolt

94.00 Capacitor

94.02 Capacitor gland

98.00 Terminal box cover

98.04 Screw

98.08 Gasket

99.00 Motor, complete

Changes reserved.

Содержание CT Series

















Отзывы: