background image

 48

1002594 ISSUE 1 M172 VARIHEAT

VARIHEAT AW SYSTEM OWNER INSTALLATION MANUAL

“Remote Damper” control – terminals 63/64/65

For control of a remote damper when Advanced Frost Protection is active. 

These are volt free contacts rated at 150mA at 230V. Contacts close when 
Advanced Frost Protection is active. 

If this facility is not required, these terminals do not need to be used.

Advanced Frost Protection

(Used when the remote damper is installed).

Advanced Frost Protection behaves in the same way as the standard Frost 
Protection with the addition of closing the remote damper. It also activates 
under the same conditions as standard, but will not deactivate when the 
temperature rises immediately. Instead, the machine will check the ambient 
temperature periodically (every six hours by default).

For each check, the remote dampers are opened for a short time (five minutes), 
fresh air is allowed to reach the probe and if the temperature has risen above 
the set point then Advanced Frost Protection is deactivated. If the temperature 
is still too cold, the machine remains in Advanced Frost Protection mode until 
the next check. An option to force a check can be found on the Set Points and 
Switches screen in the User Settings but only while Frost Protection is active.

3.9 NETWORK CONNECTION

Local area network connection

To connect the Variheat to a LAN, for screen mirroring, the RJ45 Ethernet port 
on the back of the touchscreen may be used. Take care not to confuse the 
RJ45 Ethernet port with the RJ45 COM1 port. The cable entry points on the 
electric box cover can be used to route this cable. 

A fixed IP address must be set (see section 2.2) as port forwarding must be 
completed for remote access. The default IP address is 192.168.1.150, but may 
be changed as required.

Ports to be forwarded 

80 
6000 
6002

Once forwarded, the Variheat may be accessed remotely by going to (Network 
IP address) 80 in your ActiveX enabled browser, usually Internet Explorer. If 
using the Vijeo Design’Air app, you will need to add a device to the favourites, 
enter your network IP address and leave the port number as default. See 
section 2.2 for more details.

RJ45

Ethernet

port

Local area network connection

Содержание Variheat AW1200









































































Отзывы: